Section 236 (Wheel Alignment Specifications & Adjustment Procedures): Sienna: Specifications
WARNING: This page does not describe the selected car, but rather 16 other vehicles, including the 2002 Toyota Tundra, 2002 Toyota Tacoma, 2002 Toyota Sienna, 2002 Toyota Sequoia, and 2002 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
Wheel Alignment Specifications (Sienna)
| Cold tire inflation pressure (Normal driving) | P205/70R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 , 35 bar or psi) | |||||||||
| P215/65R1595S | Front, Rear | 220 kPa (2.2 kgf/cm2
, 32 bar or psi)(1) 240 kPa (2.4 kgf/cm2 ,35 bar or psi)(2) |
||||||||||
| Cold tire inflation pressure (Trailer towing) | P205/70R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 ,35 bar or psi) | |||||||||
| P215/65R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 ,35 bar or psi) | ||||||||||
| Front wheel alignment | Vehicle height | 205/70R15 | Front(3) | 230 mm (9.06 in.) | ||||||||
| Rear(4) | 324 mm (12.76 in.) | |||||||||||
| 215/65R15 | Front(3) | 226 mm (8.90 in.) | ||||||||||
| Rear(4) | 320 mm (12.60 in.) | |||||||||||
| Camber | -0°32' ± 45' (-0.5° ± 0.75°) | |||||||||||
| Left - right error | 45' (0.75°) or less | |||||||||||
| Caster | 1°32' ± 45' (1.53° ± 0.75°) | |||||||||||
| Left-right error | 45' (0.75°) or less | |||||||||||
| Steering axis inclination | 12°35' ± 45' (12.58° ± 0.75°) | |||||||||||
| Toe-in (Total) | 0°16' ± 12' (0.27° ± 0.2°) 2.6 ± 2 mm (0.10 ± 0.08 in.) |
|||||||||||
| Rack end length difference | 1.5 mm (0.059 in.) or less | |||||||||||
| Wheel angle | Inside wheel | 34°19' ± 1° (34.32° ± 1°) | ||||||||||
| Outside wheel < Reference > | 30° 19' (30.32°) | |||||||||||
| Rear wheel alignment | Camber | -0°55' + 45' (-0.92° ± 0.75°) | ||||||||||
| Left-right error | 45' (0.75°) or less | |||||||||||
| Toe-in (Total) | 0°13' ± 18' (0.22° ± 0.30°) | |||||||||||
| 2.2 ± 3 mm (0.09 ± 0.12 in.) | ||||||||||||
| Front axle | Axle bearing backlash | Maximum | 0.05 mm (0.0020 in.) | |||||||||
| Axle hub deviation | Maximum | 0.05 mm (0.0020 in.) | ||||||||||
| Front drive shaft | Drive shaft standard length | LH | 586.0 ± 2.0 mm (23.071 ± 0.079 in.) | |||||||||
| RH | 881.6 ± 2.0 mm (34.709 ± 0.079 in.) | |||||||||||
| Front suspension | Lower ball joint turning torque | 1.0 - 3.4 N.m (10 - 35 kgf.cm, 8.7 - 30 in..lbf) | ||||||||||
| Stabilizer bar link turning torque | 0.05 -1.0 N.m (0.5-10 kgf.cm, 0.4 - 8.7 in..lbf) | |||||||||||
| Rear axle | Axle bearing backlash | Maximum | 0.05 mm (0.0020 in.) | |||||||||
| Axle hub deviation | Maximum | 0.07 mm (0.0028 in.) | ||||||||||
Measure from the ground to the center of the front side lower suspension arm mounting bolt.
Measure from the ground to the center of the axle beam bushing. |
||||||||||||