Torque Specifications
1ZZ-FE:
Tightening Torque Specification - Engine Mechanical (1ZZ-FE)
| Part Tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| Battery negative terminal x Battery | 5.4 | 55 | 48 in..lbf | |
| Engine hanger x Cylinder head sub-assy | 38 | 387 | 28 | |
| Radio setting condenser x Cylinder head sub-assy | 10 | 102 | 7 | |
| Engine coolant temperature sensor x Cylinder head sub-assy | 19.6 | 200 | 14 | |
| Exhaust manifold x Cylinder head sub-assy | 37 | 377 | 27 | |
| Exhaust manifold heat insulator No. 1 x Exhaust manifold | 18 | 184 | 13 | |
| Manifold stay x Exhaust manifold | 49 | 500 | 36 | |
| Manifold stay x Cylinder block sub-assy | 49 | 500 | 36 | |
| Knock sensor x Cylinder block sub-assy | 20 | 205 | 15 | |
| Crankshaft position sensor x Timing chain or belt cover | 9.0 | 92 | 80 in. lbf | |
| Camshaft position sensor x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Water by-pass pipe No. 1 x Cylinder block sub-assy | 9.0 | 92 | 80 in..lbf | |
| Water by-pass pipe No. 1 x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil level gage guide x Water by-pass pipe No. 1 | 13 | 133 | 10 | |
| Heated oxygen sensor x Exhaust manifold | 44 | 450 | 33 | |
| Engine mounting bracket rear x Engine mounting insulator rear | 65 | 663 | 48 | |
| Engine mounting bracket front x Engine mounting insulator front | 52 | 530 | 38 | |
| Engine mounting bracket LH x Engine mounting insulator LH | 80 | 816 | 59 | |
| Engine mounting bracket RH x Engine mounting insulator RH | 52 | 530 | 38 | |
| Front suspension crossmember sub-assy x Body | Front | 113 | 1,152 | 83 |
| (See page 14-25) | Rear | 157 | 1,601 | 116 |
| Center member x Body | 60 | 612 | 44 | |
| Return tube sub-assy x Body | Bolt A | 5.0 | 51 | 44 in..lbf |
| (See page 14-25) | Bolt B | 7.8 | 80 | 69 in. lbf |
| Cruise control actuator assy x Cruise control bracket | 6.0 | 61 | 53 in..lbf | |
| Air cleaner case x Body | 7.0 | 71 | 62 in..lbf | |
| Air cleaner case x Engine mounting bracket LH | 7.0 | 71 | 62 in..lbf | |
| Battery carrier x Body | 12.8 | 131 | 9 | |
| Battery clamp sub-assy x Body | 5.0 | 51 | 44 in..lbf | |
| Battery clamp sub-assy x Battery clamp bolt | 3.5 | 36 | 31 in..lbf | |
| Front wheel RH & LH x Front axle hub sub-assy RH & LH | 103 | 1,050 | 76 | |
| Oil strainer sub-assy x Crankshaft bearing cap sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil pan sub-assy x Crankshaft bearing cap sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil pan drain plug x Oil pan sub-assy | 37 | 377 | 27 | |
| Oil filter union x Crankshaft bearing cap sub-assy | 30 | 306 | 22 | |
| Oil filter sub-assy x Oil filter union | 13 | 133 | 10 | |
| Cylinder head sub-assy x Cylinder block sub-assy | 1st | 49 | 500 | 36 |
| (See page 14-44) | 2nd | Turn 90° | Turn 90° | Turn 90° |
| Camshaft timing gear assy x Camshaft | 54 | 551 | 40 | |
| Camshaft timing gear or sprocket x No. 2 Camshaft | 54 | 551 | 40 | |
| Camshaft bearing cap No. 1 x Cylinder head sub-assy | 23 | 235 | 17 | |
| Camshaft bearing cap No. 3 x Cylinder head sub-assy | 13 | 133 | 10 | |
| Oil control valve filter x Cylinder head sub-assy | 30 | 306 | 22 | |
| Camshaft timing oil control valve assy x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil pump assy x Cylinder block sub-assy | 9.0 | 92 | 80 in..lbf | |
| Chain vibration damper No. 1 x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Chain vibration damper No. 1 x Cylinder block sub-assy | 9.0 | 92 | 80 in..lbf | |
| Chain tensioner slipper x Cylinder block sub-assy | 18.5 | 189 | 14 | |
| Stud bolt x Timing chain cover sub-assy | 5.0 | 51 | 44 in..lbf | |
| Timing chain or belt cover sub-assy x Cylinder head sub-assy | 13 | 133 | 10 | |
| Timing chain or belt cover sub-assy x Cylinder block sub-assy | A | 13 | 133 | 10 |
| (See page 14-44) | B | 18.5 | 189 | 14 |
| Chain tensioner assy No. 1 x Timing chain or belt cover sub-assy | 9.0 | 92 | 80 in.lbf | |
| Crankshaft pulley x Crankshaft | 138 | 1,407 | 102 | |
| Water pump assy x Timing chain cover sub-assy | A | 9.0 | 92 | 80 in..lbf |
| (See page 14-44) | B | 11 | 112 | 8 |
| Engine mounting bracket RH x Timing chain or belt cover sub-assy | 47 | 479 | 35 | |
| Cylinder head cover sub-assy x Cylinder head sub-assy | A | 11 | 112 | 8 |
| (See page 14-44) | B | 9.0 | 92 | 80 in..lbf |
| Cylinder head cover sub-assy x Timing chain or belt cover sub-assy | 11 | 112 | 8 | |
| Spark plug x Cylinder head sub-assy | 25 | 255 | 18 | |
| Ventilation valve sub-assy x Cylinder head cover sub-assy | 30 | 306 | 22 | |
| V-ribbed belt tensioner assy x Cylinder head sub-assy | 29 | 296 | 21 | |
| V-ribbed belt tensioner assy x Cylinder block sub-assy | 69 | 704 | 51 | |
| Ignition coil assy x Cylinder head cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Engine wire x Cylinder head cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Engine mounting insulator RH x Body | 52 | 530 | 38 | |
| Engine mounting insulator RH x Engine mounting bracket | 52 | 530 | 38 | |
| Oil reservoir bracket No. 1 x Body | 7.8 | 80 | 69 in..lbf | |
| Cylinder head cover No. 2 x Cylinder head cover sub-assy | 7.0 | 71 | 62 in..lbf | |
| Intake manifold x Cylinder head sub-assy | 30 | 306 | 22 | |
| Drive plate & ring gear sub-assy x Crankshaft | 88 | 897 | 65 | |
| Flywheel sub-assy x Crankshaft | 1st | 49 | 500 | 36 |
| (see page 14-117) | 2nd | Turn 90° | Turn 90° | Turn 90° |
| Stud bolt x Cylinder head sub-assy | A, D and E | 9.5 | 97 | 84 in..lbf |
| (See page 14-121) | B and C | 5.0 | 51 | 44 in..lbf |
| W/ Head taper screw plug No. 2 x Cylinder head sub-assy | 44 | 449 | 33 | |
| Connecting rod cap x Connecting rod | 1st | 20 | 204 | 15 |
| (See page 14-134) | 2nd | Turn 90° | Turn 90° | Turn 90° |
| Crankshaft bearing cap sub-assy x Cylinder block sub-assy | 1st | 44 | 449 | 33 |
| (Seepage 14-134) | 2nd | Turn 90° | Turn 90° | Turn 90° |
| Others | 19 | 194 | 14 | |
| Stud bolt x Cylinder block sub-assy | A, C and D | 5.0 | 51 | 44 in..lbf |
| (See page 14-134) | B | 11 | 112 | 8 |
| E | 9.0 | 92 | 80 in..lbf | |
| Cylinder block water drain cock sub-assy x Cylinder block sub-assy | 25 | 255 | 18 | |
2ZZ-GE:
Tightening Torque Specification - Engine Mechanical (2ZZ-GE)
| Part Tightened | N.m | kgf cm | ft.lbf | |
|---|---|---|---|---|
| Cylinder head cover No. 2 x Cylinder head cover sub-assy | 7.0 | 71 | 62 in..lbf | |
| Suction hose bracket x Body | 9.8 | 100 | 87 in..lbf | |
| Cylinder head cover sub-assy x Cylinder head sub-assy | 10 | 102 | 7 | |
| Union to connector tube hose clamp x Cylinder head cover sub-assy | 7.0 | 71 | 62 in..lbf | |
| Fuel tube clamp x Cylinder head cover sub-assy | 7.5 | 76 | 66 in..lbf | |
| Wire harness protector x Cylinder head cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Ventilation No. 1 tube x Cylinder head cover sub-assy | 10 | 102 | 7 | |
| Ventilation No. 1 tube x Intake manifold | 24 | 245 | 18 | |
| Ignition coil assy x Cylinder head cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Engine hanger x Cylinder head sub-assy | 38 | 387 | 28 | |
| Engine coolant temperature sensor x Cylinder head sub-assy | 20 | 204 | 15 | |
| Camshaft position sensor x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Knock sensor x Cylinder block sub-assy | 20 | 204 | 15 | |
| Oil pressure switch assy x Cylinder head sub-assy | 15 | 153 | 11 | |
| Engine oil pressure switch assy x Crankshaft bearing cap sub-assy | 15 | 153 | 11 | |
| Crankshaft position sensor x Timing chain or belt cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Water by-pass pipe No. 1 x Cylinder block sub-assy | Nut | 10 | 102 | 7 |
| Bolt | 8.5 | 87 | 75 in..lbf | |
| Water by-pass pipe No. 1 x Cylinder head sub-assy | 21 | 214 | 15 | |
| Ventilation case No. 1 x Cylinder block sub-assy | 9.0 | 92 | 80 in..lbf | |
| Water inlet x Cylinder block sub-assy | 10 | 102 | 7 | |
| Intake manifold x Cylinder head sub-assy | 34 | 347 | 25 | |
| Intake manifold x Cylinder block sub-assy | 46 | 469 | 34 | |
| Surge tank stay No. 1 x Intake manifold | 24 | 245 | 18 | |
| Surge tank stay No. 1 x Cylinder head sub-assy | 24 | 245 | 18 | |
| Exhaust manifold x Cylinder head sub-assy | A | 50 | 510 | 16 |
| B | 21 | 214 | 37 | |
| Exhaust manifold heat insulator No. 1 x Exhaust manifold | 20 | 204 | 15 | |
| Manifold stay x Exhaust manifold | 50 | 510 | 37 | |
| Manifold stay x Cylinder block sub-assy | 50 | 510 | 37 | |
| V-ribbed belt tensioner assy x Timing chain or belt cover sub-assy | Bolt | 100 | 1,020 | 74 |
| Nut | 29 | 296 | 21 | |
| Flywheel sub-assy x Crankshaft | 1st | 49 | 500 | 36 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Transverse engine engine mounting bracket rear x Transverse engine engine mounting insulator rear | 65 | 663 | 48 | |
| Transverse engine engine mounting bracket front x Transverse engine engine mounting insulator front | 52 | 530 | 38 | |
| Transverse engine engine mounting bracket LH x Transverse engine engine mounting insulator LH | 80 | 816 | 59 | |
| Transverse engine engine mounting bracket RH x Transverse engine engine mounting insulator RH | 52 | 530 | 38 | |
| Front suspension crossmember sub-assy x Body | Front | 113 | 1,152 | 83 |
| Rear | 157 | 1,601 | 116 | |
| Engine mounting member sub-assy center x Body | 39 | 398 | 29 | |
| Vane pump oil reservoir bracket x Body | 7.8 | 80 | 69 in..lbf | |
| Return tube sub-assy x Body | Bolt A | 5.0 | 51 | 44 in..lbf |
| Bolt B | 7.8 | 80 | 69 in..lbf | |
| Cruise control actuator x Cruise control bracket | 6.0 | 61 | 53 in..lbf | |
| Air cleaner case x Body | 7.0 | 71 | 62 in..lbf | |
| Air cleaner case x Transverse engine engine mounting bracket LH | 7.0 | 71 | 62 in..lbf | |
| Battery carrier x Body | 13 | 133 | 10 | |
| Front wheel RH & LH x Front axle hub sub-assy RH & LH | 103 | 1,050 | 76 | |
| Oil pan baffle plate x Crankshaft bearing cap sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil strainer sub-assy x Crankshaft bearing cap sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil pan sub-assy x Crankshaft bearing cap sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil pan drain plug x Oil pan sub-assy | 37 | 377 | 27 | |
| Oil filter union x Crankshaft bearing cap sub-assy | 30 | 306 | 22 | |
| Cylinder head sub-assy x Cylinder block sub-assy | 1st | 35 | 357 | 26 |
| 2nd | Turn 180° | Turn 180° | Turn 180° | |
| Valve rocker shaft sub-assy x Cylinder head sub-assy | 10 | 102 | 7 | |
| Oil control valve filter x Cylinder head sub-assy | 29 | 296 | 21 | |
| Camshaft timing oil control valve assy x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Cam timing control valve housing x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Camshaft timing gear assy x Camshaft | 54 | 551 | 40 | |
| Camshaft timing gear or sprocket x No. 2 Camshaft | 54 | 551 | 40 | |
| Camshaft bearing cap x Cylinder head sub-assy | 19 | 194 | 14 | |
| Oil pump assy x Cylinder block sub-assy | 9.0 | 92 | 80 in..lbf | |
| Chain vibration damper No. 1 x Cylinder head sub-assy | 21 | 214 | 15 | |
| Chain vibration damper No. 1 x Cylinder block sub-assy | 21 | 214 | 15 | |
| Chain tensioner slipper x Cylinder block sub-assy | 21 | 214 | 15 | |
| Timing chain or belt cover sub-assy x Cylinder head sub-assy | 11 | 112 | 8 | |
| Timing chain or belt cover sub-assy x Cylinder block sub-assy | 21 | 214 | 15 | |
| Chain tensioner assy No. 1 x Timing chain or belt cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Crankshaft pulley x Crankshaft | 120 | 1,224 | 89 | |
| Transverse engine engine mounting bracket x Timing chain or belt cover sub-assy | 49 | 500 | 36 | |
| Water pump assy x Timing chain or belt cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Water pump assy x Cylinder block sub-assy | 9.0 | 92 | 80 in..lbf | |
| Water pump pulley x Water pump assy | 15 | 153 | 11 | |
| Spark plug x Cylinder head sub-assy | 18 | 184 | 13 | |
| Ventilation valve sub-assy x Cylinder head cover sub-assy | 27 | 275 | 20 | |
| Stud bolt x Timing chain or belt cover sub-assy | 9.5 | 97 | 84 in..lbf | |
| Stud bolt x Cylinder head sub-assy | A, B, D and E | 9.5 | 97 | 84 in..lbf |
| C | 5.0 | 51 | 44 in..lbf | |
| F | 19 | 194 | 14 | |
| W/ head taper screw plug No. 1 x Cylinder head sub-assy | 78 | 796 | 58 | |
| Connecting rod cap x Connecting rod | 1st | 30 | 306 | 22 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Crankshaft bearing cap sub-assy x Cylinder block sub-assy | 1st | 22 | 224 | 16 |
| 2nd | 44 | 449 | 32 | |
| 3rd | Turn 45° | Turn 45° | Turn 45° | |
| 4th | Turn 45° | Turn 45° | Turn 45° | |
| Others | 18 | 184 | 13 | |
| Stud bolt x Cylinder block sub-assy | A, B and C | 5.0 | 51 | 44 in..lbf |
| D | 19 | 194 | 14 | |
| E | 11 | 112 | 8 | |
| Sub-assy oil nozzle No. 1 x Cylinder block sub-assy | 9.0 | 92 | 80 in..lbf | |
| Screw plug x Crankshaft bearing cap sub-assy | 43 | 438 | 32 | |
| Cylinder block water drain cock sub-assy x Cylinder block sub-assy | 25 | 255 | 18 | |