Data List / Active Test
- READ DATA LIST
HINT:
Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.
- Connect the intelligent tester (with CAN VIM) to the DLC3.
- Turn the power switch ON (IG).
- Read the DATA LIST according to the display on the tester.
Power source control ECU
ITEM NORMAL CONDITION CHARTItem Measurement Item / Range (Display) Normal Condition Diagnostic Note STR UNLK SW Steering unlock switch /
ON or OFFON: Key is in key slot
OFF: No key is in key slot- READY SIG Ready signal /
ON or OFFON: Power switch ON (READY)
OFF: Power switch OFF or ON (IG) or ON (ACC)- VEHICLE SPD SIG Vehicle speed signal /
ON or OFFStop: Vehicle is stopped
Run: Vehicle is running- SHIFT P SIG Shift P signal /
ON or OFFON: Shift P signal ON (shift position is P)
OFF: Shift P signal OFF (shift position is not P)- ST READY MON Starter relay monitor /
ON or OFFON: Starter relay signal ON
OFF: Starter relay signal OFF- ACC CUT SIG Relay monitor /
ON or OFFON: ACC relay signal ON
OFF: ACC relay signal OFF- E/G COND Engine condition /
Stop or RunStop: Engine is stopped
Run: Engine is not running- SHIFT P PULSE Shift P signal pulse /
Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1Unknown: Other
Error2: Signal is abnormal and shift position is P
Normal2: Signal is normal and shift position is P
Error1: Signal is abnormal and shift position cannot be determined
Normal3: Signal is normal and shift position in not P
Error3: Signal is abnormal and shift position in not P
Normal1: Signal is normal and shift position cannot be determined- CARD H-INS SW Halfway switch /
ON or OFFON: Key is half-inserted
OFF: Key is not half-inserted- CARD F-INS SW Full switch /
ON or OFFON: Key is fully inserted
OFF: Key is not fully inserted- STOP LAMP SW1 Stop light switch 1 /
ON or OFFON: Brake pedal depressed
OFF: Brake pedal released- STOP LAMP SW2 Stop light switch 2 /
ON or OFFON: Brake pedal released
OFF: Brake pedal depressed- ST SW1 Start switch 1 /
ON or OFFON: Power switch ON (IG)
OFF: Power switch OFF- ST SW2 Start switch 2 /
ON or OFFON: Power switch ON (IG)
OFF: Power switch OFF- RATCH CIRCUIT Ratch circuit /
ON or OFFON: Power switch ON (IG)
OFF: Power switch OFF or ON (ACC) or ON (READY)- IG1 RELAY MON 1 IG1 outer relay monitor /
ON or OFFON: Power switch ON (IG)
OFF: Power switch OFF- IG1 RELAY MON 2 IG1 inner relay monitor /
ON or OFFON: Power switch ON (IG)
OFF: Power switch OFF- IG2 RELAY MON 1 States of the IG2 outer relay monitor /
ON or OFFON: Power switch ON (IG)
OFF: Power switch OFF- IG2 RELAY MON 2 IG2 Inner relay monitor /
ON or OFFON: Power switch ON (IG)
OFF: Power switch OFF- ACC RELAY MON ACC relay monitor /
ON or OFFON: Power switch ON (ACC)
OFF: Power switch OFF- PWR COND Power supply condition /
IG2 ON, ST ON, All OFF, IG1 ON or ACC ONIG2 ON: IG2 relay ON
ST ON: ST relay ON
All OFF: All relay OFF
IG1 ON: IG1 relay ON
ACC ON: ACC relay ON- - PERFORM ACTIVE TEST
HINT:
Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.
- Connect the intelligent tester (with CAN VIM) to the DLC3.
- Turn the power switch ON (IG).
- Perform the ACTIVE TEST according to the display on the tester.
Power source control ECU
ITEM TEST DETAILS DIAGNOSTIC CHARTItem Test Details Diagnostic Note KEY LOCK Key lock (turn power switch OFF during test; turn power switch ON (IG)) ON / OFF - LIGHTING IND Indicator for lighting ON / OFF - IND CONDITION Indicator Green / Red / No Sig -