Inspection Procedure
NOTE:
It is necessary to register an ID code after replacing the tire pressure warning valve and transmitter and/or the tire pressure warning ECU (see REGISTRATION
).
- IDENTIFY TRANSMITTER (CORRESPONDING TO DTC)
- Set the pressure of each tire to the specified value.
Standard pressure: 220 kPa (2.2 kgf/cm 2 , 32 psi)
- Connect the intelligent tester (with CAN VIM) to the DLC3.
- Turn the ignition switch ON.
- Select TIREPRESS by following the prompts displayed on the intelligent tester.
Tire pressure warning ECU
TIRE PRESSURE WARNING ECU CHARTItem Measurement Item / Range (Display) Normal Condition Diagnostic Note TIREPRESS1 ID1 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - TIREPRESS2 ID2 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - TIREPRESS3 ID3 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - TIREPRESS4 ID4 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - TIREPRESS5 ID5 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - - Rapidly release the tire pressure from any tire by 40 kPa (0.4 kgf/cm2
, 5.8 psi) for 30 seconds or more.
HINT:
- Identify the malfunctioning tire pressure warning valve and transmitter by rapidly releasing the tire pressures from each tire.
- Record which TIREPRESS data (ID1 to ID5) corresponds to each tire.
- Check the DATA LIST.
Result
DATA LIST CHARTCondition Detection Conditions One of TIREPRESS data (ID1 to ID5) changed Normal No TIREPRESS data changed Transmitter corresponding to DTC NOTE:- It may take up to 1 minute to display the updated tire pressure data.
- When the TIREPRESS data (IDs 1 to 5) changes, reset the tire pressure of the tires to the specified value, rotate the tires 90 to 270° and recheck.
- When the transmitter is normal, record the tire location and the transmitter ID.
- When the TIREPRESS data (IDs 1 to 5) changes, repeat the same procedure on the rest of the tires (one by one) to identify which tire pressure warning valve and transmitter the DTC corresponds to.
- Set the pressure of each tire to the specified value.
Standard pressure: 220 kPa (2.2 kgf/cm 2 , 32 psi)
- Check all transmitters of the tires.
Result
RESULT REFERENCEResult Detection Conditions One or more of transmitters abnormal A All abnormal B All normal C
B: Go to step 3
C: END
A: GO TO NEXT STEP.
- Set the pressure of each tire to the specified value.
- CHECK TIRE PRESSURE WARNING VALVE AND TRANSMITTER
- Select REGIT ID CODE by following the prompts displayed on the intelligent tester.
Tire pressure warning ECU
TIRE PRESSURE WARNING ECUItem Measurement Item / Range (Display) Normal Condition Diagnostic Note REGIT ID1 CODE Registered ID1 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID1 is display - REGIT ID2 CODE Registered ID2 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID2 is display - REGIT ID3 CODE Registered ID3 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID3 is display - REGIT ID4 CODE Registered ID4 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID4 is display - REGIT ID5 CODE Registered ID5 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID5 is display - - Remove the tire pressure warning valve and transmitter and check its ID number (see REMOVAL ).
- Check whether the recorded transmitter ID and the actual transmitter ID match.
Result
RESULT CHARTResult Detection Conditions Unmatched A Matched B
B: REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
A: PERFORM REGISTRATION (TRANSMITTER ID)
- Select REGIT ID CODE by following the prompts displayed on the intelligent tester.
- CHECK WIRE HARNESS (ECU - RECEIVER)
- Disconnect the E56 ECU connector.
- Disconnect the L20 receiver connector.
- Measure the resistance of the wire harness side connectors.
Standard resistance
STANDARD RESISTANCE CHARTTester Connection Specified Condition E56-8 (RF5V) - L20-5 (+5V) Below 1 Ω E56-7 (RDA) - L20-1 (RDA) E56-16 (GND2) - L20-4 (GND)
NG: REPAIR OR REPLACE HARNESS AND CONNECTOR
OK: GO TO NEXT STEP.
- READ VALUE OF INTELLIGENT TESTER (TIRE PRESSURE)
- Check the DATA LIST tire pressure valve.
Tire pressure warning ECU
TIRE PRESSURE WARNING ECUItem Measurement Item / Range (Display) Normal Condition Diagnostic Note TIREPRESS1 ID1 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - TIREPRESS2 ID2 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - TIREPRESS3 ID3 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - TIREPRESS4 ID4 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - TIREPRESS5 ID5 tire pressure/minimum: 0 kPa (0 kgf/cm2 , 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2 , 92.5 psi) Actual tire pressure - OK: All tire pressure readings are equal to the actual tire pressure.
NOTE: It may take up to 1 minute to display the updated tire pressure data.
OK: END
NG: GO TO NEXT STEP.
- Check the DATA LIST tire pressure valve.
- CHECK ID CODE (TIRE PRESSURE WARNING VALVE AND TRANSMITTER)
- Select REGIT ID CODE by following the prompts displayed on the intelligent tester.
Tire pressure warning ECU
TIRE PRESSURE WARNING ECU CHARTItem Measurement Item / Range (Display) Normal Condition Diagnostic Note REGIT ID1 CODE Registered ID1 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID1 is display - REGIT ID2 CODE Registered ID2 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID2 is display - REGIT ID3 CODE Registered ID3 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID3 is display - REGIT ID4 CODE Registered ID4 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID4 is display - REGIT ID5 CODE Registered ID5 code/minimum: 0 maximum: FFFFFFF The ID No. registered in transmitter ID5 is display - - Remove the tire pressure monitor valve and transmitter check its ID number (see REMOVAL ).
- Check whether the recorded transmitter ID and the actual transmitter ID match.
Result
RESULT CHARTResult Detection Conditions Unmatched A Matched B
B: REPLACE TIRE PRESSUREWARNING RECEIVER AND TRANSMITTER
A: PERFORM REGISTRATION (TRANSMITTER ID)
- Select REGIT ID CODE by following the prompts displayed on the intelligent tester.