LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2007 >> Sienna LE, AWD >> Repair and Diagnosis >> Body & Frame >> Windows >> Windshield/WINDOWGLASS >> POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function) >> Operation Check
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Operation Check

  1. CHECK WINDOW LOCK SWITCH 
    1. Check that the passenger side power window and slide door power window operation is disabled when the window lock switch of the power window master switch is pressed.
    2. Check that the passenger side power window and slide door power windows can be operated when the window lock switch is pressed again.
  2. CHECK MANUAL UP/DOWN FUNCTION 
    Fig 1: Checking Window Lock Switch
    G04967105Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Check that the driver side power window can be operated using the AUTO (driver side) switch of the power window master switch as follows:

      Standard 

      POWER WINDOW MASTER SWITCH OPERATION REFERENCE

      Condition Master Switch Switch Operation Power Window
      Ignition switch ON AUTO (driver side) Pull halfway up UP (Closed)
      Push halfway down DOWN (Open)
    2. Check that the passenger power window and slide door power windows can be operated using each power window regulator switch as follows:

      Standard 

      POWER WINDOW MASTER SWITCH OPERATION REFERENCE

      Condition Master Switch Switch Operation Power Window
      • Ignition switch ON
      • Window lock switch OFF
      		 Passenger side Pull up UP (Closed)
      Push down DOWN (Open)
      Rear LH Pull up UP (Closed)
      Push down DOWN (Open)
      Rear RH Pull up UP (Closed)
      Push down DOWN (Open)
  3. CHECK AUTO UP/DOWN FUNCTION 
    1. Check that the driver side power window can be operated using the AUTO (driver side) switch of the power window master switch as follows:

      Standard 

      POWER WINDOW MASTER SWITCH OPERATION REFERENCE

      Condition Master Switch Switch Operation Power Window
      Ignition switch ON AUTO (driver side) Pull halfway up AUTO UP (Fully closed)
      Push halfway down AUTO DOWN (Fully open)
  4. CHECK REMOTE MANUAL UP/DOWN FUNCTION 
    1. Check that the passenger side power window and slide door power window can be operated using each switch of the power window master switch as follows:

      Standard 

      POWER WINDOW MASTER SWITCH OPERATION REFERENCE

      Condition Master Switch Switch Operation Power Window
      • Ignition switch ON
      • Window lock switch OFF
      		 Passenger side Pull up UP (Closed)
      Push down DOWN (Open)
      Rear LH Pull up UP (Closed)
      Push down DOWN (Open)
      Rear RH Pull up UP (Closed)
      Push down DOWN (Open)
  5. CHECK MANUAL DOWN FUNCTION VIA TRANSMITTER 
    1. Check that all power windows and sliding roof (standard type only) operate as follows when operating the transmitter:

      Standard 

      POWER WINDOW MASTER SWITCH OPERATION REFERENCE

      Condition Transmitter Operation Position/Operation
      • No key in ignition key cylinder
      • Any door UNLOCK
      		 Press UNLOCK switch pressed for 1.5 sec. or more All power windows go DOWN
      • No key in ignition key cylinder
      • All doors CLOSE
      • All doors LOCK
      		 Press LOCK switch pressed for 1.5 sec. or more All power windows go UP

      HINT:

      For a sign for starting operation, the wireless door lock buzzer sounds once (answer-back).

  6. CHECK POWER WINDOW OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF 
    1. When both of the following conditions are fulfilled, check that the power windows can be operated even after the ignition switch is turned off.
      1. Within 45 seconds after the ignition switch is turned off.
      2. The front doors are closed.
  7. CHECK JAM PROTECTION FUNCTION 

    HINT:

    The jam protection function prevents any part of your body from getting caught by accident between the door frame and the door glass during power window operation.

    NOTE: If the power window motor has been reset, raise and lower the door glass several times using MANUAL function before performing the check.
    Fig 2: Checking Jam Protection Function
    G04967106Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Check that the door glass goes down by approx. 50 mm (1.97 in.) right when something gets caught between the door frame and door glass during power window operation. However, when the opening between the door frame and the door glass is less than 200 mm (7.87 in.), the door glass keeps going down until the operation reaches 200 mm (7.87 in.) and stops there.
      • AUTO UP
      • AUTO UP operation after the ignition switch OFF
      • MANUAL UP operation after the ignition switch OFF
  8. CHECK POWER WINDOW FAIL-SAFE FUNCTION 
    1. If there is a malfunction in the pulse sensor of the power window motor, the power window function will be restricted to partial operation.
      POWER WINDOW MASTER SWITCH OPERATION REFERENCE

      Power Window Function (Switch Operation) Ignition Switch ON Ignition Switch OFF
      Manual UP (Pull halfway up) Disabled (1) Disabled
      Manual DOWN (Push halfway down) Operative Disabled
      AUTO UP (Pull fully up) Disabled Disabled
      AUTO DOWN (Push fully down) Disabled Disabled
      (1) However, manual UP function of the power window is operative when fully pulling up the power window switch.
scientia non olet · About LEMON Manuals