LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2008 >> Corolla S, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 53 (Cruise Control System) >> Cruise Control System >> Diagnosis System
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis System

WARNING: This page is about a different car, the 2007 Toyota Camry Solara. However, it is still accessible from the selected car via links, so may be relevant.
  1. DESCRIPTION 

    The ECU controls the cruise control system of the vehicle. The data and DTCs relating to the cruise control system can be read from the DLC3 of the vehicle. If either DTC or CRUISE OK is not displayed on the multi-information display on the combination meter when checking for DTCs, there may be a problem with either the combination meter or the CAN communication and multiplex communication systems. Use the intelligent tester to check and solve the problem.

  2. CHECK DLC3 
    1. The ECU uses the ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format.
      Fig 1: Identifying DLC3 Connector Terminals (CANL And BAT)
      G04828034Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      COMMUNICATION CHART

      Terminal No. (Symbols) Terminal Description Condition Specified Condition
      SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
      CG (4) - Body ground Chassis ground Always Below 1 Ω
      SG (5) - Body ground Signal ground Always Below 1 Ω
      BAT (16) - Body ground Battery positive Always 10 to 14 V
      CANH (6) - CANL (14) CAN bus line Ignition switch off(1) 54 to 69 Ω
      CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off(1) 200 Ω or higher
      CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off(1) 200 Ω or higher
      CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch off(1) 6 kΩ or higher
      CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch off(1) 6 kΩ or higher
      (1) Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.

      If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

    2. Connect the cable of the intelligent tester to the DLC3, turn the ignition switch to the ON position, and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem with either the vehicle or the tester.
      • If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
      • If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.
  3. CHECK INDICATOR 
    1. Turn the ignition switch to the ON position.
    2. Check that the CRUISE main indicator light illuminates when the cruise control main switch is turned on, and that the indicator light turns off when the main switch is turned off. If the results are not as specified, inspect the CRUISE MAIN INDICATOR LIGHT CIRCUIT  .

      HINT:

      While driving with cruise control, the ECM activates AUTO CANCEL of the cruise control system when a malfunction occurs in one of the following: vehicle speed sensors, stop light switch, or other related parts. When AUTO CANCEL is activated, the CRUISE main indicator light outputs the blinking pattern as shown in the illustration. At the same time, data of the malfunction is stored as a DTC.

      Fig 2: Checking CRUISE Main Indicator Light
      G05131886Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals