Service Data
Front Axle Hub
FRONT AXLE HUB - SERVICE DATA
| Axle hub bearing looseness | Maximum | 0.05 mm (0.00197 in.) |
| Axle hub runout | Maximum | 0.08 mm (0.00315 in.) |
Front Axle Hub
FRONT AXLE HUB - SERVICE DATA
| Rear Axle shaft runout | Maximum | 1.50 mm (0.0591 in.) |
| Rear Axle flange runout | Maximum | 0.05 mm (0.00197 in.) |
Front Differential
FRONT DIFFERENTIAL - SERVICE DATA
| Companion flange runout | Vertical | Maximum: 0.10 mm (0.00394 in.) |
| Lateral | Maximum: 0.10 mm (0.00394 in.) | |
| Drive pinion preload (at starting) | New bearing | 3.0 to 3.5 N*m (31 to 35 kgf*cm, 27 to 50 in.*lbf) |
| Reused bearing | 2.1 to 2.5 N*m (22 to 24 kgf*cm, 19 to 21 in.*lbf) | |
| Total preload (at starting) | New bearing | Drive pinion preload plus 1.6 to 2.4 N*m (17 to 24 kgf*cm, 15 to 21 in.*lbf) |
| Reused bearing | Drive pinion preload plus 1.3 to 2.1 N*m (14 to 21 kgf*cm, 12 to 18 in.*lbf) | |
| Drive pinion to ring gear backlash | 0.17 to 0.27 mm (0.00670 to 0.0106 in.) | |
| Side gear backlash | 0 to 0.15 mm (0 to 0.00591 in.) | |
| Side gear thrust washer thickness | 1.43 to 1.47 mm (0.0563 to 0.0579 in.) | |
| 1.48 to 1.52 mm (0.0583 to 0.0598 in.) | ||
| 1.53 to 1.57 mm (0.0602 to 0.0618 in.) | ||
| 1.58 to 1.62 mm (0.0622 to 0.0638 in.) | ||
| 1.63 to 1.67 mm (0.0642 to 0.0657 in.) | ||
| 1.68 to 1.72 mm (0.0661 to 0.0677 in.) | ||
| 1.73 to 1.77 mm (0.0681 to 0.0697 in.) | ||
| 1.78 to 1.82 mm (0.0701 to 0.0717 in.) | ||
| 1.83 to 1.87 mm (0.0720 to 0.0736 in.) | ||
| Plate washer thickness | 1.49 to 1.51 mm (0.0587 to 0.0594 in.) | |
| 1.51 to 1.53 mm (0.0594 to 0.0602 in.) | ||
| 1.53 to 1.55 mm (0.0602 to 0.0610 in.) | ||
| 1.55 to 1.57 mm (0.0610 to 0.0618 in.) | ||
| 1.57 to 1.59 mm (0.0618 to 0.0626 in.) | ||
| 1.59 to 1.61 mm (0.0626 to 0.0634 in.) | ||
| 1.61 to 1.63 mm (0.0634 to 0.0642 in.) | ||
| 1.63 to 1.65 mm (0.0642 to 0.0650 in.) | ||
| 1.65 to 1.67 mm (0.0650 to 0.0657 in.) | ||
| 1.67 to 1.69 mm (0.0657 to 0.0665 in.) | ||
| 1.69 to 1.71 mm (0.0665 to 0.0673 in.) | ||
| 1.71 to 1.73 mm (0.0673 to 0.0681 in.) | ||
| 1.73 to 1.75 mm (0.0681 to 0.0689 in.) | ||
| 1.75 to 1.77 mm (0.0689 to 0.0697 in.) | ||
| 1.77 to 1.79 mm (0.0697 to 0.0705 in.) | ||
| 1.79 to 1.81 mm (0.0705 to 0.0713 in.) | ||
| 1.81 to 1.83 mm (0.0713 to 0.0720 in.) | ||
| 1.83 to 1.85 mm (0.0720 to 0.0728 in.) | ||
| 1.85 to 1.87 mm (0.0728 to 0.0736 in.) | ||
| 1.87 to 1.89 mm (0.0736 to 0.0744 in.) | ||
| 1.89 to 1.91 mm (0.0744 to 0.0752 in.) | ||
| 1.91 to 1.93 mm (0.0752 to 0.0760 in.) | ||
| 1.93 to 1.95 mm (0.0760 to 0.0768 in.) | ||
| 1.95 to 1.97 mm (0.0768 to 0.0776 in.) | ||
| 1.97 to 1.99 mm (0.0776 to 0.0783 in.) | ||
| 1.99 to 2.01 mm (0.0783 to 0.0791 in.) | ||
| 2.01 to 2.03 mm (0.0791 to 0.0799 in.) | ||
| 2.03 to 2.05 mm (0.0799 to 0.0807 in.) | ||
| 2.05 to 2.07 mm (0.0807 to 0.0815 in.) | ||
| 2.07 to 2.09 mm (0.0815 to 0.0823 in.) | ||
| 2.09 to 2.11 mm (0.0823 to 0.0831 in.) | ||
| 2.11 to 2.13 mm (0.0831 to 0.0839 in.) | ||
| 2.13 to 2.15 mm (0.0839 to 0.0846 in.) | ||
| 2.15 to 2.17 mm (0.0846 to 0.0854 in.) | ||
| 2.17 to 2.19 mm (0.0854 to 0.0862 in.) | ||
| 2.19 to 2.21 mm (0.0862 to 0.0870 in.) | ||
| 2.21 to 2.23 mm (0.0870 to 0.0878 in.) | ||
| 2.23 to 2.25 mm (0.0878 to 0.0886 in.] | ||
| 2.25 to 2.27 mm (0.0886 to 0.0894 in.] | ||
| 2.27 to 2.29 mm (0.0894 to 0.0902 in.; | ||
| 2.29 to 2.31 mm (0.0902 to 0.0909 in.) | ||
| 2.31 to 2.33 mm (0.0909 to 0.0917 in.) | ||
| 2.33 to 2.35 mm (0.0917 to 0.0925 in.) | ||
| Drive pinion washer thickness | 1.815 to 1.835 mm (0.07146 to 0.07224 in.) | |
| 1.840 to 1.860 mm (0.07244 to 0.07323 in.) | ||
| 1.865 to 1.885 mm (0.07343 to 0.07421 in.) | ||
| 1.890 to 1.910 mm (0.07441 to 0.07520 in.) | ||
| 1.915 to 1.935 mm (0.07539 to 0.07618 in.) | ||
| 1.940 to 1.960 mm (0.07638 to 0.07717 in.) | ||
| 1.965 to 1.985 mm (0.07736 to 0.07815 in.) | ||
| 1.990 to 2.010 mm (0.07835 to 0.07913 in.) | ||
| 2.015 to 2.035 mm (0.07933 to 0.08012 in.) | ||
| 2.040 to 2.060 mm (0.08031 to 0.08110 in.) | ||
| 2.065 to 2.085 mm (0.08130 to 0.08209 in.) | ||
| 2.090 to 2.110 mm (0.08228 to 0.08307 in.) | ||
| 2.115 to 2.135 mm (0.08327 to 0.08405 in.) | ||
| 2.140 to 2.160 mm (0.08425 to 0.08504 in.) | ||
| 2.165 to 2.185 mm (0.08524 to 0.08602 in.) | ||
| 2.190 to 2.210 mm (0.08622 to 0.08701 in.) | ||
| 2.215 to 2.235 mm (0.08720 to 0.08799 in.) | ||
| 2.240 to 2.260 mm (0.08819 to 0.08898 in.) | ||
| 2.265 to 2.285 mm (0.08917 to 0.08996 in.) | ||
Rear Differential
REAR DIFFERENTIAL - SERVICE DATA
| Companion flange runout | Vertical | Maximum: 0.10 mm (0.00394 in.) |
| Lateral | Maximum: 0.10 mm (0.00394 in.) | |
| Ring gear runout | Maximum: 0.05 mm (0.00197 in.) | |
| Drive pinion to ring gear backlash | 0.10 to 0.20 mm (0.00394 to 0.00787 in.) | |
| Drive pinion preload (at starting) | New bearing | 1.0 to 1.7 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf) |
| Reused bearing | 0.9 to 1.4 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf) | |
| Total preload (at starting) | New bearing | Drive pinion preload plus 0.4 to 0.6 N*m (5 to 6 kgf*cm, 4 to 5 in.*lbf) |
| Reused bearing | Drive pinion preload plus 0.4 to 0.6 N*m (5 to 6 kgf*cm, 4 to 5 in.*lbf) | |
| Differential case runout | Maximum: 0.04 mm (0.00157 in.) | |
| Side gear backlash | 0.02 to 0.15 mm (0.00787 to 0.00591 in.) | |
| Side gear thrust Washer thickness | 1.53 to 1.57 mm (0.0602 to 0.0618 in.) | |
| 1.58 to 1.62 mm (0.0622 to 0.0638 in.) | ||
| 1.63 to 1.67 mm (0.0642 to 0.0657 in.) | ||
| 1.68 to 1.72 mm (0.0661 to 0.0677 in.) | ||
| 1.73 to 1.77 mm (0.0681 to 0.0697 in.) | ||
| 1.78 to 1.82 mm (0.0701 to 0.0171 in.) | ||
| 1.83 to 1.87 mm (0.0720 to 0.0736 in.) | ||
| 1.88 to 1.92 mm (0.0740 to 0.0756 in.) | ||
| 1.93 to 1.97 mm (0.0760 to 0.0776 in.) | ||
| 1.98 to 2.02 mm (0.0780 to 0.0795 in.) | ||
| 2.03 to 2.07 mm (0.0799 to 0.0815 in.) | ||
| 2.08 to 2.12 mm (0.0820 to 0.0835 in.) | ||
| Plate washer thickness | 1.04 to 1.06 mm (0.0409 to 0.0417 in.) | |
| 1.065 to 1.085 mm (0.0420 to 0.0427 in.) | ||
| 1.09 to 1.11 mm (0.0419 to 0.0437 in.) | ||
| 1.115 to 1.135 mm (0.0439 to 0.0447 in.) | ||
| 1.14 to 1.16 mm (0.0449 to 0.0457 in.) | ||
| 1.165 to 1.185 mm (0.0459 to 0.0467 in.) | ||
| 1.19 to 1.21 mm (0.0469 to 0.0476 in.) | ||
| 1.215 to 1.235 mm (0.0478 to 0.0486 in.) | ||
| 1.24 to 1.26 mm (0.0488 to 0.0496 in.) | ||
| 1.265 to 1.285 mm (0.0498 to 0.0506 in.) | ||
| 1.29 to 1.31 mm (0.0508 to 0.0516 in.) | ||
| 1.315 to 1.335 mm (0.0518 to 0.0526 in.) | ||
| 1.34 to 1.36 mm (0.0528 to 0.0535 in.) | ||
| 1.365 to 1.385 mm (0.0537 to 0.0545 in.) | ||
| 1.39 to 1.41 mm (0.0547 to 0.0555 in.) | ||
| 1.415 to 1.435 mm (0.0558 to 0.0565 in.) | ||
| 1.44 to 1.46 mm (0.0567 to 0.0575 in.) | ||
| 1.465 to 1.485 mm (0.0577 to 0.0585 in.) | ||
| 1.49 to 1.51 mm (0.0587 to 0.0595 in.) | ||
| 1.515 to 1.535 mm (0.0597 to 0.0605 in.) | ||
| 1.54 to 1.56 mm (0.0607 to 0.0615 in.) | ||