Inspection Procedure

1. Turn the ignition switch off.
2. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   RESISTANCE SPECIFIED CONDITIONS
   
   

   Tester Connection	Condition	Specified Condition
   D1-6 (CANH) - D1-14 (CANL)	Ignition switch off	108 to 132 Ω

   Fig 1: Identifying Terminal CANL And CANH Of DLC3 Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Result 

   RESULT CHART
   
   

   Result	Proceed to
   108 to 132 Ω	A
   132 Ω or higher	B

   NOTE: When the measured value is 133 Ω or more and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING " after repairing the trouble area.

B : REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR (CANH, CANL) 

A: Go to next step 

1. Turn the ignition switch off.
2. Disconnect the ECM connector (E5).
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   RESISTANCE SPECIFIED CONDITIONS
   
   

   Tester Connection	Condition	Specified Condition
   E5-15 (CANH) - E5-31 (CANL)	Ignition switch off	108 to 132 Ω

   Fig 2: Identifying Terminal CANH And CANL Of E5 ECM Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: Go to step 3 

OK: REPLACE ECM  (See REMOVAL )

1. Reconnect the ECM connector.
2. Disconnect the skid control ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   RESISTANCE SPECIFIED CONDITIONS
   
   

   Tester Connection	Condition	Specified Condition
   S1-11 (CANH) - S1-25 (CANL)	Ignition switch off	108 to 132 Ω

   Fig 3: Identifying Terminal CANL And CANH Of S1 Connector

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: Go to step 4 

OK: REPLACE SKID CONTROL ECU WITH ACTUATOR  (See REMOVAL )

1. Reconnect the skid control ECU connector.
2. Disconnect the CAN junction connector.
Fig 4: Identifying J11 CAN Junction Connector
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   RESISTANCE SPECIFIED CONDITIONS
   
   

   Tester Connection	Connect to	Condition	Specified Condition
   J11-7 (CANH) - J11-18 (CANL)	Skid control ECU	Ignition switch off	108 to 132 Ω
   J11-11 (CANH) - J11-22 (CANL)	ECM	Ignition switch off	108 to 132 Ω

   Result 

   RESULT CHART
   
   

   Result	Proceed to
   OK	A
   NG (ECM main wire)	B
   NG (Skid control ECU main wire)	C

B : REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (JUNCTION CONNECTOR - ECM) 

C : REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR - SKID CONTROL ECU) 

A : REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR)