Trouble in Passenger Airbag ON/OFF Indicator (FROM 12/2010): Procedure

1. Turn the ignition switch on (IG), and check the SRS warning light condition.

   HINT: 

   If this trouble occurs, the SRS warning light is off. If it is on, a DTC is output. Troubleshoot for the output DTC.

   OK

   The SRS warning light does not come on.

NG → See step   9 

OK: Go to next step 

1. Turn the ignition switch on (IG).
2. Check if the passenger airbag ON/OFF indicator correctly indicates the front passenger seat condition.

   OK

   Front passenger seat condition	ON Indicator	OFF Indicator
   Adult is seated.	ON	OFF
   Child is seated.	OFF	ON
   Vacant	OFF	OFF
   Occupant classification system failure.	OFF	ON

OK → END 

NG: Go to next step 

1. Turn the ignition switch off.
2. Connect the Techstream to the DLC3.
3. Turn the ignition switch on (IG).
4. Using the Techstream, perform "Zero point calibration". Refer to INITIALIZATION .

   OK

   The "Zero Point Calibration is complete." is displayed.

NG → See step   5 

OK: Go to next step 

1. Using the Techstream, perform "Sensitivity check". Refer to INITIALIZATION .

   Standard value

   27 to 33 kg (59.52 to 72.75 lb)

NG → See step   5 

OK → END 

1. Turn the ignition switch off.
2. Loosen the 4 installation bolts of the front seat assembly RH.
3. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

   Torque: 37 N*m (380 kgf*cm, 27 ft.*lbf) 

NEXT: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch on (IG).
3. Using the Techstream, perform "Zero point calibration". Refer to INITIALIZATION .

   OK

   The "Zero Point Calibration is complete." is displayed.

NG → See step   8 

OK: Go to next step 

1. Using the Techstream, perform "Sensitivity check". Refer to INITIALIZATION .

   Standard value

   27 to 33 kg (59.52 to 72.75 lb)

NG → See step   8 

OK → END 

1. Turn the ignition switch off.
2. Disconnect the negative (-) terminal cable from the battery.
3. Check the connectors are properly connected to the occupant classification ECU and the 4 occupant classification sensors.

   OK

   The connectors are connected.

4. Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.
5. Check the connectors are not damaged or deformed.

   OK

   The connectors are normal.

NG → REPAIR OR REPLACE CONNECTOR, THEN GO TO STEP  1 

OK: Go to next step 

1. Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.
2. Connect the negative (-) terminal cable to the battery.
3. Turn the ignition switch on (IG), and wait for at least 60 seconds.
4. Clear the DTCs stored in the occupant classification ECU. Refer to DTC CHECK / CLEAR .
5. Clear the DTCs stored in the center airbag sensor assembly. Refer to DTC CHECK / CLEAR .
6. Turn the ignition switch off.
7. Turn the ignition switch on (IG), and wait for at least 60 seconds.
8. Check the DTCs. Refer to DTC CHECK / CLEAR .

   OK

   DTC is not output.

NG → REPLACE CENTER AIRBAG SENSOR ASSEMBLY 

OK: Go to next step 

1. Turn the ignition switch off.
2. Disconnect the negative (-) terminal cable from the battery.
3. Replace the occupant classification ECU. Refer to REMOVAL .

NEXT: Go to next step 

1. Connect the negative (-) terminal cable to the battery.
2. Connect the Techstream to the DLC3.
3. Turn the ignition switch on (IG).
4. Using the Techstream, perform "Zero point calibration". Refer to INITIALIZATION .

   OK

   The "Zero Point Calibration is complete." is displayed.

NEXT: Go to next step 

1. Using the Techstream, perform "Sensitivity check". Refer to INITIALIZATION .

   Standard value

   27 to 33 kg (59.52 to 72.75 lb)

NEXT → END