LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2008 >> Yaris Base, 2D Hatchback, Standard >> Repair and Diagnosis >> Engine Performance >> Engine Control System (1NZ-FE) >> SFI System >> ECM Power Source Circuit >> Inspection Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Inspection Procedure

  1. INSPECT INTEGRATION RELAY (POWER SOURCE OF INTEGRATION RELAY) 
    1. Remove the integration relay from the engine room relay block.
    2. Measure the voltage between the terminal of the integration relay and body ground.

      Standard voltage 

      TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

      Tester Connections Specified Conditions
      Engine room relay block (1C-1) - Body ground 11 to 14 V
      Fig 1: Identifying Integration Relay (Integration Relay - Body Ground)
      G04828325Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reinstall the integration relay.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INTEGRATION RELAY) 

    OK: Go to Next Step 

  2. INSPECT INTEGRATION RELAY (EFI RELAY AND IG2 RELAY) 
    1. Remove the integration relay from the engine room relay block.
    2. Inspect the EFI fuse and the AM2 fuse.
      1. Remove the EFI fuse and AM2 fuse from the integration relay.
      2. Check the resistance of the EFI fuse and AM2 fuse.

        Standard resistance: Below 1 Ω 

      3. Reinstall the EFI fuse and the AM2 fuse.
    3. Inspect the EFI relay and the IG2 relay.
      1. Check the resistance between the terminals shown below.

        Standard resistance 

        TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

        Tester Connections Specified Conditions
        1C-1 - 1A-4 10 kΩ or higher
        Below 1 Ω (when battery voltage is applied to terminals 1A-2 and 1A-3)
        1C-1 - 1B-4 10 kΩ or higher
        Below 1 Ω (when battery voltage is applied to terminals 1A-2 and 1A-3)
        1C-1 - 1B-1 Below 1 Ω
        Fig 2: Identifying Integration Relay (EFI Relay And IG2 Relay)
        G04828326Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Reinstall the integration relay.

    NG: REPLACE INTEGRATION RELAY 

    OK: Go to Next Step 

  3. CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT) 
    Fig 3: Checking Harness And Connector (+B, +B2 And MREL Circuit)
    G04828327Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Check the harness and the connectors between the integration relay and the ECM.
      1. Remove the integration relay from the engine room relay block.
      2. Disconnect the A21 ECM connector.
      3. Check the resistance.

        Standard resistance (Check for open) 

        TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

        Tester Connections Specified Conditions
        MREL (A21-44) - Engine room relay block (1A-2) Below 1 Ω
        +B (A21-2) - Engine room relay block (1A-4)
        +B2 (A21-1) - Engine room relay block (1A-4)

        Standard resistance (Check for short) 

        TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

        Tester Connections Specified Conditions
        MREL (A21-44) or Engine room relay block (1A-2) - Body ground 10 kΩ or higher
        +B (A21-2) or Engine room relay block (1A-4) - Body ground
        +B2 (A21-1) or Engine room relay block (1A-4) - Body ground
    2. Check the harness and the connector between the integration relay and body ground.
      1. Check the resistance.

        Standard resistance (Check for open) 

        TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

        Tester Connections Specified Conditions
        Engine room relay block (1A-3) - Body ground Below 1 Ω
    3. Reinstall the integration relay.
    4. Reconnect the ECM connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to Next Step 

  4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) 
    Fig 4: Identifying Harness And Connector (ECM - Body Ground)
    G04828328Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the C20 ECM connector.
    2. Check the resistance.

      Standard resistance (Check for open) 

      TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

      Tester Connections Specified Conditions
      E1 (C20-104) - Body ground Below 1 Ω
    3. Reconnect the ECM connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to Next Step 

  5. INSPECT ECM (IGSW VOLTAGE) 
    Fig 5: Identifying ECM (IGSW Voltage)
    G04828329Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the C20 and A21 ECM connectors.
    2. Turn the ignition switch to ON.
    3. Measure the voltage between the terminals of the C20 and A21 ECM connectors.

      Standard voltage 

      TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

      Tester Connections Specified Conditions
      IGSW (A21-28) - E1 (C20-104) 11 to 14 V
    4. Reconnect the ECM connectors.

    OK: REPLACE ECM (See  REMOVAL   ) 

    NG: Go to Next Step 

  6. INSPECT FUSE (IGN FUSE) 
    1. Remove the IGN fuse from the main body ECU.
      2. Fig 6: Identifying IGN Fuse From Main Body ECU
      G04828330Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the IGN fuse resistance.

      Standard resistance: Below 1 Ω 

    3. Reinstall the IGN fuse.

    NG: CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE 

    OK: Go to Next Step 

  7. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM) 
    Fig 7: Identifying Harness And Connector (Integration Relay - ECM, Integration Relay - Body Ground)
    G04828331Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the integration relay from the engine room relay block.
    2. Disconnect the A21 ECM connector.
    3. Check the resistance.

      Standard resistance (Check for open) 

      TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

      Tester Connections Specified Conditions
      Engine room relay block (1B-4) - IGSW (A21-28) Below 1 Ω

      Standard resistance (Check for short) 

      TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

      Tester Connections Specified Conditions
      Engine room relay block (1B-4) or IGSW (A21-28) - Body ground 10 kΩ or higher
    4. Reinstall the integration relay.
    5. Reconnect the ECM connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to Next Step 

  8. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - IGNITION SWITCH) 
    1. Check the harness and the connectors between the integration relay and the ignition switch.
      Fig 8: Identifying Harness And Connector (Integration Relay - Ignition Switch)
      G04828332Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the integration relay from the engine room relay block.
      2. Disconnect the D8 ignition switch connector.
      3. Check the resistance.

        Standard resistance (Check for open) 

        TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

        Tester Connections Specified Conditions
        Engine room relay block (1B-2) - IG2 (D8-6) Below 1 Ω

        Standard resistance (Check for short) 

        TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

        Tester Connections Specified Conditions
        Engine room relay block (1B-2) or IG2 (D8-6) - Body ground 10 kΩ or higher
    2. Check the harness and the connectors between the integration relay and body ground.
      1. Check the resistance.

        Standard resistance (Check for open) 

        TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

        Tester Connections Specified Conditions
        Engine room relay block (1B-3) - Body ground Below 1 Ω
    3. Reinstall the integration relay.
    4. Reconnect the ignition switch connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to Next Step 

  9. INSPECT IGNITION SWITCH 
    1. Disconnect the D8 ignition switch connector.
      2. Fig 9: Identifying Terminals Of D8 Ignition Switch Connector
      G04828333Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the resistance between the terminals shown below.

      Standard resistance 

      TESTER CONNECTIONS SPECIFIED CONDITIONS CHART

      Key Positions Tester Connections Specified Conditions
      LOCK - 10 kΩ or higher
      ACC 2-4 Below 1 Ω
      ON 1-2-4
      5-6
      START 1-3-4
      5-6-7
    3. Reconnect the ignition switch connector.

    NG: REPLACE IGNITION SWITCH 

    OK: REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - INTEGRATION RELAY) 

scientia non olet · About LEMON Manuals