LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2009 >> Matrix Base, Automatic >> Repair and Diagnosis (Single Page) >> Restraints >> Air Bag, SRS >> Supplemental Restraint System >> Occupant Classification System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
  1. DATA LIST FOR OCCUPANT CLASSIFICATION ECU 
    1. Turn the ignition switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON and turn the Techstream on.
    4. Enter the following menus: Body Electrical / Occupant Detection / Data List.
    5. Check the values by referring to the table below.

      HINT:

      The "Specified Condition for Zero Point Calibration" in the table below must be satisfied when zero point calibration is performed.

    Data List 

    TESTER DISPLAY NORMAL CONDITION CHART

    Tester Display Measurement Item/Range Normal Condition Specified Condition for Zero Point Calibration Diagnostic Note
    Passenger Classification Passenger classification/
    NG: Data is not determined
    AM50: Adult is seated and seat is in rear position
    AF05: Adult is seated and seat is in front position
    CHILD: Child is seated OFF: Vacant    		 AM50/AF05/CHILD/ OFF OFF -
    Passenger Buckle SW Buckle switch (Passenger side)/
    Set: Passenger side seat belt is fastened
    Unset: Passenger side seat belt is unfastened
    NG: Data is not determined    		 Unset/Set Unset -
    Pressure Sensor Output Pressure sensor output/
    Min.: 0
    Max.: 255    		 0 to 210 0 to 2 -
    Filtered Pressure Sensor Output Filtered pressure sensor output/
    Min.: 0
    Max.: 255    		 38 to 240 38 to 75 If value is outside range of "Specified Condition for Zero Point Calibration", check whether any objects placed on seat cushion and that seat cushion fitted correctly.
    Thermistor Temperature Output Thermistor temperature output/
    Min.: -40°C (-40°F)
    Max.: 90°C (194°F)    		 -40 to 85°C (-40 to 185°F) 3 to 40°C (37 to 104°F) If value is outside range of "Specified Condition for Zero Point Calibration", adjust temperature to proper range by using air conditioner, etc.
    Weight Threshold Weight threshold/
    Min.: 0
    Max.: 255    		 36 to 67 (reference value) 36 to 67 (reference value) -
    Filtered Belt Tension Output Filtered belt tension output/
    Min.: 0
    Max.: 255    		 39 to 229 39 to 64 (no load) -
    Empty Threshold Value from the Seat Factory Empty threshold value from seat factory/
    Min.: 0
    Max.: 255    		 38 to 75 38 to 75 -
    Allow Threshold Threshold value for adult passenger or not from seat factory/
    Min.: 0
    Max.: 255    		 43 to 64 (reference value) 43 to 64 (reference value) -
    Number of Present DTC Number of present trouble codes/
    Min.: 0
    Max.: 255    		 0 0 -
    Number of Past DTC Number of past trouble codes/
    Min.: 0
    Max.: 255    		 0 0 -
scientia non olet · About LEMON Manuals