Valve Body Assembly: Inspection

1. Measure the resistance according to the value(s) in the table below.

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   Solenoid Connector (S1) - Solenoid Body (S1)	15 to 25°C (59 to 77°F)	11 to 15 Ω

   If the value is not as specified, replace the shift solenoid valve S1.

2. Connect a positive (+) battery lead to the terminal of the solenoid connector, and a negative (-) battery lead to the solenoid body, and check the operation of the valve.
   NOTE: When using battery voltage during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.
   Fig 1: Inspecting Shift Solenoid Valve S1

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   OK: The solenoid makes an operating sound  .

   If the operation cannot be done as specified, replace the shift solenoid valve S1.

1. Measure the resistance according to the value(s) in the table below.

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   Solenoid Connector (S2) - Solenoid Body (S2)	15 to 25°C (59 to 77°F)	11 to 15 Ω

   If the value is not as specified, replace the shift solenoid valve S2.

2. Connect a positive (+) battery lead to the terminal of the solenoid connector, and a negative (-) battery lead to the solenoid body, and check the operation of the valve.

Fig 2: Inspecting Shift Solenoid Valve S2

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

OK: The solenoid makes an operating sound  .

If the operation cannot be done as specified, replace the shift solenoid valve S2.

1. Measure the resistance according to the value(s) in the table below.

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   Solenoid Connector (ST) - Solenoid Body (ST)	15 to 25°C (59 to 77°F)	11 to 15 Ω

   If the value is not as specified, replace the shift solenoid valve ST.

2. Connect a positive (+) battery lead to the terminal of the solenoid connector, and a negative (-) battery lead to the solenoid body, and check the operation of the valve.

OK: The solenoid makes an operating sound  .

If the operation cannot be done as specified, replace the shift solenoid valve ST.

Fig 3: Inspecting Shift Solenoid Valve ST

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Measure the resistance according to the value(s) in the table below.

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   1 - 2	20°C (68°F)	5.0 to 5.6 Ω

   If the value is not as specified, replace the shift solenoid valve SLT.

2. Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

OK: The solenoid makes an operating sound  .

If the operation cannot be done as specified, replace the shift solenoid valve SLT.

Fig 4: Inspecting Shift Solenoid Valve SLT

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Measure the resistance according to the value(s) in the table below.

   Standard Resistance 

   Fig 5: Inspecting Shift Solenoid Valve SLU

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   1 - 2	20°C (68°F)	5.0 to 5.6 Ω

   If the value is not as specified, replace the shift solenoid valve SLU.

2. Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.

OK: The solenoid makes an operating sound  .

If the operation cannot be done as specified, replace the shift solenoid valve SLU.