LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2009 >> Matrix Base, Standard >> Repair and Diagnosis >> Body & Frame >> Power Windows & Glass >> Quarter Window Glass >> Removal
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Quarter Window Glass: Removal

  1. REMOVE REAR DOOR SCUFF PLATE LH  (See REMOVAL )
  2. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH  (See REMOVAL )
  3. REMOVE REAR SEAT CUSHION ASSEMBLY  (See REMOVAL )
  4. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side) 
  5. REMOVE REAR SEATBACK OUTER HINGE COVER (for LH Side)  (See REMOVAL )
  6. REMOVE REAR SEATBACK INNER HINGE COVER (for LH Side)  (See REMOVAL )
  7. REMOVE REAR SEATBACK ASSEMBLY LH  (See REMOVAL )
  8. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) 
  9. REMOVE DECK BOARD ASSEMBLY  (See REMOVAL )
  10. REMOVE NO. 2 DECK BOARD  (See REMOVAL )
  11. REMOVE JACK CARRIER ASSEMBLY 
  12. REMOVE JACK ASSEMBLY  (See REMOVAL )
  13. REMOVE DECK FLOOR BOX LH  (See REMOVAL )
  14. REMOVE DECK FLOOR BOX RH  (See REMOVAL )
  15. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR  (See CHILD RESTRAINT SEAT TETHER ANCHOR )
  16. REMOVE LUGGAGE COMPARTMENT TRAY  (See REMOVAL )
  17. REMOVE REAR DECK TRIM COVER  (See REMOVAL )
  18. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY (for LH Side)  (See REMOVAL )
  19. REMOVE REAR SEAT SIDE GARNISH LH  (See REMOVAL )
  20. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH  (See REMOVAL )
  21. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)  (See REMOVAL )
  22. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)  (See REMOVAL )
  23. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH  (See REMOVAL )
  24. REMOVE SIDE DECK TRIM PANEL ASSEMBLY LH  (See REMOVAL )
  25. REMOVE QUARTER PILLAR GARNISH LH  (See REMOVAL )
  26. REMOVE ROOF SIDE INNER GARNISH LH  (See REMOVAL )
  27. REMOVE QUARTER WINDOW ASSEMBLY 
    1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
      Fig 1: Applying Protective Tape To Outer Surface Of Vehicle Body To Prevent Scratches
      G06038200Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a knife, cut off the quarter window moulding as shown in the illustration.
      NOTE: Make a partial cut in the moulding. Then pull and remove it by hand.
      Fig 2: Cutting Off Quarter Window Moulding
      G06038201Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Pass a piano wire between the from interior vehicle body and glass from the interior as shown in the illustration.
    4. Tie both wire ends to wooden blocks or similar objects that can serve as handle.
      NOTE: When separating the quarter window assembly from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
    5. Cut off the adhesive by pulling the piano wire around the quarter window assembly.
      NOTE: Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.
      Fig 3: Identifying Piano Wire
      G06038202Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disengage the 3 clips.
    7. Using a suction cup, remove the glass.
    NOTE: Be careful not to drop the glass.
    Fig 4: Identifying Glass And Clips
    G06038203Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. CLEAN VEHICLE BODY 
    1. Clean and shape the contact surfaces of the vehicle body.
      1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.
      NOTE: Be careful not to damage the vehicle body.

      HINT:

      Leave as much adhesive on the vehicle body as possible.

      Fig 5: Identifying Adhesive On Vehicle Body
      G05421268Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

      HINT:

      Even if all the adhesive has been removed, clean the vehicle body.

scientia non olet · About LEMON Manuals