Transmission Control Cable: Installation

WARNING: This page is about a different variant/trim than selected.

INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
1. Install the transmission control cable assembly with the 2 nuts.
  Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
  
  Fig 1: Locating Transmission Control Cable Assembly Nuts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the transmission control cable assembly with the nut.
  Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
  
  Fig 2: Locating Transmission Control Cable Assembly Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the 2 transmission control cables to the control cable bracket with 2 new clips*1.
4. Install the 2 transmission control cables to the transaxle with the 2 clips*2.
  
  Fig 3: Identifying Transmission Control Cables And Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Rotate the transmission control cable nut counterclockwise approximately 180° and, while holding the nut in that position, press in the stopper until it makes 2 click sounds.
  
  Fig 4: Rotating Transmission Control Cable Nut Counterclockwise Approximately 180°
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Install the outer part of the transmission control cable to the shift lever retainer, check that the position of the spring is the same as A shown in the illustration, and push in the stopper.
  HINT:
  
  If the stopper cannot be pushed in, slightly rotate the nut clockwise and then push in the stopper.
  
  Fig 5: Checking Position Of Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.
  
  Fig 6: Pushing Two Claws Together At Top Of Transmission Control Cable Lock Piece
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Install the control shift cable to the shift lever assembly.
9. Install the control select cable to the shift lever assembly.
  NOTE:
  - Make sure that the lock piece is protruding from the adjuster case.
  - Make sure to adjust the length at the neutral shift position.
10. Press in and lock the lock piece to the adjuster case.
  
  Fig 7: Pressing In Lock Piece To Adjuster Case
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  NOTE: Securely press in the lock piece until the lock engages.
ADJUST TRANSMISSION CONTROL SELECT CABLE (See ADJUSTMENT )
INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL (See INSTALLATION )
INSTALL FRONT NO. 1 CONSOLE BOX INSERT (See INSTALLATION )
INSTALL FRONT NO. 2 CONSOLE BOX INSERT (See REMOVAL )
INSTALL FRONT CONSOLE BOX ASSEMBLY (See INSTALLATION )
INSTALL CONSOLE BOX CARPET
INSTALL NO. 2 SWITCH HOLE BASE (See INSTALLATION )
INSTALL FRONT UPPER CONSOLE BOX (See INSTALLATION )
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (See INSTALLATION )
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (See INSTALLATION )
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (See INSTALLATION )
INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
1. Install the No. 1 front floor heat insulator with the 3 nuts.
  Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
INSTALL CENTER EXHAUST PIPE ASSEMBLY (See INSTALLATION )
INSTALL AIR CLEANER CASE (See REASSEMBLY )
INSTALL AIR CLEANER CAP SUB-ASSEMBLY (See WIRING DIAGRAM )

Fig 8: Locating No. 1 Front Floor Heat Insulator Nuts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (See REASSEMBLY )
INSPECT FOR EXHAUST GAS LEAK