LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2009 >> RAV4 Base, 2.5 F, AWD >> Repair and Diagnosis >> General Information >> OEM General Information >> Service Specifications >> 2GR-FE Engine Mechanical >> Service Data
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Service Data

2GR-FE ENGINE MECHANICAL - SERVICE DATA

Engine Ignition timing When using the Techstream 8 to 12° BTDC @ idle
When not using the Techstream Connect SST 8 to 12° BTDC @ idle
Disconnect SST 5 to 15° BTDC @ idle
Idle speed When using the Techstream 600 to 700 rpm
When not using the Techstream 600 to 700 rpm
Compression Compression pressure 1.3 MPa (13 kgf/cm2 , 189 psi) or more
Minimum pressure 0.98 MPa (10.0 kgf/cm2 , 142 psi)
Difference between each cylinder 0.1 MPa (1.0 kgf/cm2 , 15 psi) or less
Intake manifold Warpage Maximum Intake manifold side 0.8 mm (0.031 in.)
Cylinder head side 0.2 mm (0.008 in.)
Exhaust manifold Warpage Maximum 0.70 mm (0.0028 in.)
Connecting rod Thrust clearance Standard 0.15 to 0.40 mm (0.0059 to 0.0157 in.)
Maximum 0.50 mm (0.0197 in.)
Oil clearance Standard 0.045 to 0.067 mm (0.0018 to 0.0026 in.)
Maximum 0.070 mm (0.0028 in.)
Big end inside diameter Mark 1 56.000 to 56.006 mm (2.2047 to 2.2050 in.)
Mark 2 56.007 to 56.012 mm (2.2050 to 2.2052 in.)
Mark 3 56.013 to 56.018 mm (2.2052 to 2.2054 in.)
Mark 4 56.019 to 56.024 mm (2.2055 to 2.2057 in.)
Standard sized bearing center wall thickness Mark 1 1.481 to 1.484 mm (0.0583 to 0.0584 in.)
Mark 2 1.484 to 1.487 mm (0.0584 to 0.0585 in.)
Mark 3 1.487 to 1.490 mm (0.0585 to 0.0587 in.)
Mark 4 1.490 to 1.493 mm (0.0587 to 0.0588 in.)
Bend Maximum 0.05 mm (0.0020 in.) per 100 mm (3.94 in.)
Twist Maximum 0.15 mm (0.0059 in.) per 100 mm (3.94 in.)
Crankshaft Pin diameter Standard 52.992 to 53.000 mm (2.0863 to 2.0866 in.)
Thrust clearance Standard 0.04 to 0.24 mm (0.0016 to 0.0094 in.)
Maximum 0.30 mm (0.0118 in.)
Thrust washer thickness Standard 2.43 to 2.48 mm (0.0957 to 0.0976 in.)
Main journal diameter Standard Mark 00 60.999 to 61.000 mm (2.4015 to 2.4016 in.)
Mark 01 60.998 to 60.999 mm (2.4015 to 2.4015 in.)
Mark 02 60.997 to 60.998 mm (2.4015 to 2.4015 in.)
Mark 03 60.996 to 60.997 mm (2.4014 to 2.4015 in.)
Mark 04 60.995 to 60.996 mm (2.4014 to 2.4014 in.)
Mark 05 60.994 to 60.995 mm (2.4013 to 2.4014 in.)
Mark 06 60.993 to 60.994 mm (2.4013 to 2.4013 in.)
Mark 07 60.992 to 60.993 mm (2.4013 to 2.4013 in.)
Mark 08 60.991 to 60.992 mm (2.4012 to 2.4013 in.)
Mark 09 60.990 to 60.991 mm (2.4012 to 2.4012 in.)
Mark 10 60.989 to 60.990 mm (2.4011 to 2.4012 in.)
Mark 11 60.988 to 60.989 mm (2.4011 to 2.4011 in.)
Crankshaft Upper bearing center wall thickness Standard No. 1 and No. 4 journal Mark 1 2.500 to 2.503 mm (0.0984 to 0.0985 in.)
Mark 2 2.503 to 2.506 mm (0.0985 to 0.0987 in.)
Mark 3 2.506 to 2.509 mm (0.0987 to 0.0988 in.)
Mark 4 2.509 to 2.512 mm (0.0988 to 0.0989 in.)
Mark 5 2.512 to 2.515 mm (0.0989 to 0.0990 in.)
Standard No. 2 and No. 3 journal Mark 1 2.478 to 2.481 mm (0.0976 to 0.0977 in.)
Mark 2 2.481 to 2.484 mm (0.0977 to 0.0978 in.)
Mark 3 2.484 to 2.487 mm (0.0978 to 0.0979 in.)
Mark 4 2.487 to 2.490 mm (0.0979 to 0.0980 in.)
Mark 5 2.490 to 2.493 mm (0.0980 to 0.0981 in.)
Crankshaft Lower bearing center wall thickness Standard No. 1 and No. 4 journal Mark 1 2.478 to 2.481 mm (0.0976 to 0.0977 in.)
Mark 2 2.481 to 2.484 mm (0.0977 to 0.0978 in.)
Mark 3 2.484 to 2.487 mm (0.0978 to 0.0979 in.)
Mark 4 2.487 to 2.490 mm (0.0979 to 0.0980 in.)
Mark 5 2.490 to 2.493 mm (0.0980 to 0.0981 in.)
Standard No. 2 and No. 3 journal Mark 1 2.500 to 2.503 mm (0.0984 to 0.0985 in.)
Mark 2 2.503 to 2.506 mm (0.0985 to 0.0987 in.)
Mark 3 2.506 to 2.509 mm (0.0987 to 0.0988 in.)
Mark 4 2.509 to 2.512 mm (0.0988 to 0.0989 in.)
Mark 5 2.512 to 2.515 mm (0.0989 to 0.0990 in.)
Circle runout Maximum 0.06 mm (0.0024 in.)
Journal diameter Standard 60.988 to 61.00 mm (2.4011 to 2.4016 in.)
Taper and out-of-round Maximum 0.02 mm (0.0008 in.)
Crank pin diameter Standard 52.992 to 53.000 mm (2.0863 to 2.0866 in.)
Taper and out-of-round Maximum Taper and out-of-round 0.02 mm (0.0008 in.)
Camshaft Circle runout Maximum 0.04 mm (0.0016 in.)
Cam lobe height Standard Intake 44.316 to 44.416 mm (1.7447 to 1.7487 in.)
Exhaust 44.262 to 44.362 mm (1.7426 to 1.7465 in.)
Maximum Intake 44.166 mm (1.7388 in.)
Exhaust 44.112 mm (1.7367 in.)
Journal diameter Standard No. 1 journal 35.946 to 35.960 mm (1.4152 to 1.4157 in.)
Other journal 25.959 to 25.975 mm (1.0220 to 1.0226 in.)
Thrust clearance(bank 1) Standard 0.08 to 0.13 mm (0.0031 to 0.0051 in.)
Maximum 0.15 mm (0.006 in.)
Thrust clearance (bank 2) Standard 0.08 to 0.13 mm (0.0031 to 0.0051 in.)
Maximum 0.15 mm (0.006 in.)
Oil clearance Standard No. 1 journal 0.040 to 0.079 mm (0.0016 to 0.0031 in.)
Other journal 0.025 to 0.062 mm (0.0010 to 0.0024 in.)
Maximum No. 1 Journal 0.10 mm (0.0039 in.)
Other journal 0.09 mm (0.0035 in.)
Timing chain Chain elongation Maximum 136.9 mm (5.389 in.)
No. 2 timing chain Chain elongation Maximum 137.6 mm (5.417 in.)
Crankshaft timing gear or sprocket Sprocket diameter (w/ chain) Minimum 61.4 mm (2.417 in.)
Idle sprocket Sprocket diameter (w/ chain) Minimum 61.4 mm (2.417 in.)
Idle gear shaft Idle gear shaft diameter Standard 22.987 to 23.000 mm (0.9050 to 0.9055 in.)
Idle gear inside diameter Standard 23.02 to 23.03 mm (0.9062 to 0.9067 in.)
Oil clearance Standard 0.02 to 0.043 mm (0.0008 to 0.0017 in.)
Maximum 0.043 mm (0.0017 in.)
No. 2 chain tensioner Depth Maximum 0.9 mm (0.035 in.)
No. 3 chain tensioner Depth Maximum 0.9 mm (0.035 in.)
Chain tensioner slipper Depth Maximum 1.0 mm (0.039 in.)
No. 1 chain vibration damper Depth Maximum 1.0 mm (0.039 in.)
No. 2 chain vibration damper Depth Maximum 1.0 mm (0.039 in.)
Cylinder head Warpage Standard Cylinder head lower side 0.05 mm (0.0020 in.)
Intake side 0.08 mm (0.0031 in.)
Exhaust side 0.08 mm (0.0031 in.)
Maximum 0.10 mm (0.0039 in.)
Protrusion height Standard 18.0 to 19.0 mm (0.71 to 0.75 in.)
Intake valve guide bush Cylinder bore diameter Standard 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
Bush bore diameter Standard Use STD 10.335 to 10.356 mm (0.4069 to 0.4077 in.)
Use O/S 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
Protrusion height Standard 9.1 to 9.9 mm (0.3582 to 0.3900 in.)
Exhaust valve guide bush Cylinder bore diameter Standard 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
Bush bore diameter Standard Use STD 10.335 to 10.356 mm (0.4069 to 0.4077 in.)
Use O/S 0.05 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
Protrusion height Standard 9.30 to 9.70 mm (0.3661 to 0.3819 in.)
Intake valve Valve stem diameter Standard 5.470 to 5.485 mm (0.2154 to 0.2159 in.)
Margin thickness Standard 1.0 mm (0.0394 in.)
Minimum 0.50 mm (0.0197 in.)
Overall length Standard 105.85 mm (4.1673 in.)
Minimum 105.35 mm (4.1476 in.)
Exhaust valve Valve stem diameter Standard 5.465 to 5.480 mm (0.2151 to 0.2157 in.)
Margin thickness Standard 1.0 mm (0.0394 in.)
Minimum 0.50 mm (0.0197 in.)
Overall length Standard 110.40 mm (4.3464 in.)
Minimum 109.90 mm (4.3268 in.)
Inner compression spring Free length Standard 45.46 mm (1.7898 in.)
Deviation Maximum 1.0 mm (0.039 in.)
Angle (reference) Maximum 2°
Valve guide bush Bush inside diameter Standard 5.51 to 5.53 mm (0.2169 to 0.2177 in.)
Clearance Standard Intake 0.025 to 0.060 m (0.0010 to 0.0024 in.)
Exhaust 0.030 to 0.065 mm (0.0012 to 0.0026 in.)
Maximum Intake 0.08 mm (0.0031 in.)
Exhaust 0.10 mm (0.0039 in.)
Cylinder block Warpage Maximum 0.07 mm (0.0028 in.)
Bore diameter Standard 94.000 to 94.012 mm (3.7008 to 3.7013 in.)
Maximum 94.200 mm (3.7087 in.)
Piston Diameter Standard 93.960 to 93.980 mm (3.6992 to 3.7000 in.)
Maximum 93.830 mm (3.6941 in.)
Distance 8.9 mm (0.3504 in.)
Oil clearance Standard 0.020 to 0.052 mm (0.0007 to 0.0020 in.)
Maximum 0.06 mm (0.0024 in.)
Ring groove clearance Standard No. 1 0.020 to 0.070 mm (0.0008 to 0.0028 in.)
No. 2 0.020 to 0.060 mm (0.0008 to 0.0024 in.)
Oil 0.070 to 0.150 mm (0.0028 to 0.0059 in.)
Ring end gap Standard No. 1 0.25 to 0.35 mm (0.0098 to 0.0138 in.)
No. 2 0.50 to 0.60 mm (0.0197 to 0.0236 in.)
Oil 0.10 to 0.40 mm (0.0039 to 0.0157 in.)
Maximum No. 1 0.50 mm (0.0197 in.)
No. 2 0.85 mm (0.0335 in.)
Oil 0.60 mm (0.0236 in.)
Piston pin hole inside diameter Standard Mark A 22.001 to 22.004 mm (0.8662 to 0.8663 in.)
Mark B 22.005 to 22.007 mm (0.8663 to 0.8664 in.)
Mark C 22.008 to 22.010 mm (0.8665 to 0.8665 in.)
piston pin diameter Standard Mark A 21.997 to 22.000 mm (0.8660 to 0.8661 in.)
Mark B 22.001 to 22.003 mm (0.8662 to 0.8663 in.)
Mark C 22.004 to 22.006 mm (0.8663 to 0.8664 in.)
Oil clearance Standard 0.001 to 0.007 mm (0.00004 to 0.0003 in.)
Maximum 0.015 mm (0.0006 in.)
Bush inside diameter Standard Mark A 22.005 to 22.008 mm (0.8663 to 0.8665 in.)
Mark B 22.009 to 22.011 mm (0.8665 to 0.8666 in.)
Mark C 22.012 to 22.014 mm (0.8666 to 0.8667 in.)
Oil clearance Standard 0.005 to 0.011 mm (0.0002 to 0.0004 in.)
Maximum 0.03 mm (0.0012 in.)
Crankshaft bearing cap set bolt Diameter Standard 10.8 to 11.0 mm (0.4252 to 0.4331 in.)
Minimum 10.70 mm (0.4213 in.)
Cylinder head set bolt Outside diameter Minimum 10.70 mm (0.4213 in.)
Connecting rod bolt Diameter Standard 7.2 to 7.3 mm (0.283 to 0.287 in.)
Minimum 7.0 mm (0.276 in.)
scientia non olet · About LEMON Manuals