Oil And Oil Filter: Replacement

CAUTION:

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.

DRAIN ENGINE OIL
1. Remove the oil filler cap.
2. Remove the oil drain plug, and drain the oil into a container.
3. Clean and install the oil drain plug with a new gasket.
  Torque: 40 N*m (408 kgf*cm, 30 ft.*lbf)
REMOVE OIL FILTER ELEMENT
1. Connect the hose with an inside diameter of 15 mm (0.59 in.) to the pipe.
  
  Fig 1: Connecting Hose To Pipe
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Remove the oil filter drain plug from the oil filter cap.
  
  Fig 2: Removing Oil Filter Drain Plug
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Insert the pipe with the hose into the oil filter cap.
  NOTE: Be sure to insert the pipe with the O-ring installed on the oil filter cap side.
  
  HINT:
  
  Place the hose end into a container before draining oil from the hose.
  
  Fig 3: Inserting Pipe With Hose Into Oil Filter Cap
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Make sure that oil is completely drained, and remove the pipe and O-ring.
  HINT:
  
  Be sure to turn the pipe in the direction of the arrow to remove it.
  
  Fig 4: Removing Pipe And O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Using SST, remove the oil filter cap.
  SST 09228-06501
  
  Fig 5: Removing Oil Filter Cap
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Remove the oil filter element and O-ring from the oil filter cap.
  NOTE: Do not use any tools to remove the O-ring in order to prevent the cap from being damaged. Be sure to remove it by hand.
  
  Fig 6: Identifying Oil Filter Element, Oil Filter Cap And O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL OIL FILTER ELEMENT
1. Clean the inside of the oil filter cap, threads, and O-ring groove.
2. Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.
  NOTE: Make sure that the O-ring does not get twisted on the groove.
3. Install a new oil filter element to the oil filter cap.
4. Remove all dirt and foreign matter from the installation surface and the inside of the cap on the engine side.
  
  Fig 7: Identifying Oil Filter Element, Oil Filter Cap And O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Apply a light coat of engine oil to the O-ring again and install the oil filter cap.
  NOTE: Make sure that the O-ring does not get caught between the parts.
6. Using SST, install the oil filter cap.
  SST 09228-06501
  
  Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf)
  
  NOTE: Make sure that there is no clearance between the parts after tightening the oil filter cap.
  
  Fig 8: Installing Oil Filter Cap
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.
  NOTE: Remove all dirt and foreign matter from the installation surface.
8. Install the oil filter drain plug to the oil filter cap.
  Torque: 13 N*m (127 kgf*cm, 10 ft.*lbf)
  
  NOTE: Make sure that the O-ring does not get caught between the parts.
  
  Fig 9: Installing Oil Filter Cap
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

ADD ENGINE OIL

Add clean engine oil and install the oil filler cap.

Engine oil

ENGINE OIL SPECIFICATION

Oil Grade	Oil Viscosity (SAE)
ILSAC multigrade engine oil	5W-30

Capacity:

CAPACITY SPECIFICATION

Item	Standard Condition
Drain and refill with oil filter change	6.1 liters (6.4 US qts, 5.4 Imp. qts)
Drain and refill without oil filter change	5.7 liters (6.0 US qts, 5.0 Imp. qts)
Dry fill	7.1 liters (7.5 US qts, 6.2 Imp. qts)

INSPECT FOR OIL LEAK
1. Start the engine. Check for engine oil leaks from the connected parts of the oil filter cap and oil filter drain plug.