Freeze Frame Data
WARNING: This page is about a different car, the 2009 Toyota Sequoia. However, it is still accessible from the selected car via links, so may be relevant.
- FREEZE FRAME DATA
- The skid control ECU stores the current vehicle (sensor) state as freeze frame data when a DTC is detected, or when the ABS, BA, TRAC or VSC are operating.
The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS, BA, TRAC or VSC was activated.
HINT:
- The skid control ECU will not count the number of times the ignition switch is turned ON if the vehicle does not drive at a speed of at least 7 km/h (4.3 mph), or a DTC is detected.
- Freeze frame data at the time the ABS, BA, TRAC or VSC operates:
The skid control ECU stores and updates the data whenever the ABS, BA, TRAC or VSC system operates.
When the ECU stores data at the time a DTC is detected, the data stored when the ABS, BA, TRAC or VSC operated may be cleared.
- Freeze frame data at the time a DTC is detected: When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.
- Connect the Techstream (with CAN VIM) or Techstream to the DLC3.
- Turn the ignition switch to ON.
- From the display on the Techstream, select the FREEZE FRAME DATA.
Skid Control ECU
SKID CONTROL ECU SPECIFICATIONTester Display Measurement Item Reference Value Elapsed Time after Freeze Trigger Elapsed time after freeze trigger Min.: 0 msec, Max.: 500 msec. Number of IG ON Number of operations of ignition switch ON after storing freeze frame data 0 to 31 Stop Lamp SW Stop light switch signal Stop light switch ON: ON, OFF: OFF Parking Brake SW Parking brake switch signal Parking brake switch ON: ON, OFF: OFF Gear Position Gear position information FAIL
1st
2nd
3rd
4th
5th
6th
P, N
R
NOT ROperated System Operated system status ABS activated: ABS
VSC activated: VSC
TRAC activated: TRAC
BA activated: BA
HAB activated: HAB
Fail-safe mode activated: FAIL
PBA activated: PBA
PB activated: PB
Hill-start assist control activated: HA-CTRL
System prohibited: SYS
No system activated: NONMaster Cylinder Sensor Master cylinder pressure sensor reading Min.: 0 V, Max.: 5 V M/C Sensor Grade Master cylinder pressure sensor change Min.: -30 MPa/sec, Max.: 255 MPa/sec. Stroke Sensor Stroke sensor reading Min.: 0 V, Max.: 5 V Stroke Sensor Grade Stroke sensor grade Min.: -2560 mm/s, Max.: 2550 mm/s Yaw Rate Sensor Yaw rate sensor reading Min.: -128°/sec, Max.: 127°/sec. Lateral G Lateral G Min.: -25.11 m/sec.2 , Max.: 24.91 m/sec.2 Forward and Rearward G Forward and rearward G Min.: -25.11 m/sec.2 , Max.: 24.91 m/sec.2 FR Wheel Speed Front right wheel speed reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) FL Wheel Speed Front left wheel speed reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) RR Wheel Speed Rear right wheel speed reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) RL Wheel Speed Rear left wheel speed reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle Speed Vehicle speed reading Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle Speed Grade Vehicle speed grade Min.: -25.11 m/sec.2 , Max.: 24.91 m/sec.2 Real Engine Torque Real engine torque Min.: -1024 Nm, Max.: 1023 Nm Steering Angle Sensor Steering angle sensor reading Min.: -3276.8°
Max.: 3276.7°TRAC/VSC Off Mode TRAC/VSC Off Mode Normal mode
TRAC OFF mode
VSC OFF mode
- The skid control ECU stores the current vehicle (sensor) state as freeze frame data when a DTC is detected, or when the ABS, BA, TRAC or VSC are operating.