LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2011 >> Matrix Base, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 24 (Engine Control System SFI System (Diagnostic Codes (P0010 - P0128))) >> SFI System >> DTC P0011: Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (FROM 12/2010); DTC P0012: Camshaft Position "A" - Timing Over-Retarded (Bank 1) (FROM 12/2010); DTC P0021: Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) (FROM 12/2010); DTC P0022: Camshaft Position "A" - Timing Over-Retarded (Bank 2) (FROM 12/2010) >> Confirmation Driving Pattern
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Confirmation Driving Pattern

WARNING: This page is about a different car, the 2011 Toyota Avalon. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: View Of Driving Pattern Graph
GTY303907Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure). Refer to DTC CHECK / CLEAR .
  4. Turn the ignition switch off and wait for 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the ignition and warm it up until the engine coolant temperature reaches 75°C (167°F) or more [B].
  7. Drive the vehicle for 5 minutes or more [C].
  8. Idle the engine for 30 seconds or more [D].
  9. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
  10. Read the pending DTCs [E].
  11. If a pending DTC is output, the system is malfunctioning.

    HINT: 

    If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  13. Input the DTC: P0011, P0012, P0021 or P0022.
  14. Check the DTC judgment result.
    Techstream Display Description
    NORMAL
    • DTC judgment completed
    • System normal
    ABNORMAL
    • DTC judgment completed
    • System abnormal
    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions
    UNKNOWN
    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit
    WARNING:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT: 

    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [F] through [H].
  15. Drive the vehicle for 5 minutes or more [F].
  16. Idle the engine for 30 seconds or more [G].
  17. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  18. Input the DTC: P0011, P0012, P0021 or P0022.
  19. Check the DTC judgment result again [H].

    HINT: 

    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows NORMAL, the system is normal.
  20. If the test result is INCOMPLETE or UNKNOWN and no pending DTC is output, perform a universal trip and check for permanent DTCs. Refer to DTC CHECK / CLEAR .

    HINT: 

    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTC is output, the system is normal.
scientia non olet · About LEMON Manuals