LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2012 >> Matrix Base, Automatic Trans >> Repair and Diagnosis (Single Page) >> External Pages >> Different variant/trim >> Section 10 (Manual Transmission (E351) (Service Information)) >> Transmission Control Cable >> Installation >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Transmission Control Cable: Installation: Installation

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Install the transmission control cable assembly with the 2 nuts.

      Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

      Fig 1: Locating Transmission Control Cable Assembly Nuts
      GTY219987Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the transmission control cable assembly with the nut.
      Fig 2: Locating Transmission Control Cable Assembly Nut
      GTY235722Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

    3. Install the 2 transmission control cables to the control cable bracket with 2 new clips*1.
      Fig 3: Identifying Transmission Control Cables And Clips
      GTY204957Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the 2 transmission control cables to the transaxle with the 2 clips*2.
    5. Rotate the transmission control cable nut counterclockwise approximately 180° and, while holding the nut in that position, press in the stopper until it makes 2 click sounds.
      Fig 4: Rotating Transmission Control Cable Nut
      GTY183189Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Install the outer part of the transmission control cable to the shift lever retainer, check that the position of the spring is the same as A shown in the illustration, and push in the stopper.

      HINT: 

      If the stopper cannot be pushed in, slightly rotate the nut clockwise and then push in the stopper.

      Fig 5: Installing Outer Part Of Transmission Control Cable
      GTY172531Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.
      Fig 6: Pushing Two Claws Together At Top Of Transmission Control Cable Lock Piece
      GTY244693Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Install the control shift cable to the shift lever assembly.
      Fig 7: Pressing In And Lock Piece To Adjuster Case
      GTY220435Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Install the control select cable to the shift lever assembly.
      NOTE:
      • Make sure that the lock piece is protruding from the adjuster case.
      • Make sure to adjust the length at the neutral shift position.
    10. Press in and lock the lock piece to the adjuster case.
      NOTE:

      Securely press in the lock piece until the lock engages.

  2. ADJUST TRANSMISSION CONTROL SELECT CABLE  See step  1
  3. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL  . Refer to INSTALLATION - Step 15
  4. INSTALL FRONT NO. 1 CONSOLE BOX INSERT  . Refer to INSTALLATION - Step 17
  5. INSTALL FRONT NO. 2 CONSOLE BOX INSERT  . Refer to REMOVAL - Step 33
  6. INSTALL FRONT CONSOLE BOX ASSEMBLY  . Refer to INSTALLATION - Step 1
  7. INSTALL CONSOLE BOX CARPET 
  8. INSTALL NO. 2 SWITCH HOLE BASE  . Refer to INSTALLATION - Step 22
  9. INSTALL FRONT UPPER CONSOLE BOX  . Refer to INSTALLATION - Step 23
  10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY  . Refer to INSTALLATION - Step 5
  11. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY  . Refer to INSTALLATION - Step 7
  12. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY  . Refer to INSTALLATION - Step 17
  13. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR 
    1. Install the No. 1 front floor heat insulator with the 3 nuts.
      Fig 8: Locating No. 1 Front Floor Heat Insulator Nuts
      GTY227239Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

  14. INSTALL CENTER EXHAUST PIPE ASSEMBLY  . Refer to INSTALLATION - Step 3
  15. INSTALL AIR CLEANER CASE  . Refer to INSTALLATION - Step 64
  16. INSTALL AIR CLEANER CAP SUB-ASSEMBLY  . Refer to INSTALLATION - Step 2
  17. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY  . Refer to INSTALLATION - Step 93
  18. INSPECT FOR EXHAUST GAS LEAK 
scientia non olet · About LEMON Manuals