Data List / Active Test

Use the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Air Conditioner / Data List.
5. Check the value(s) by referring to the table below.
   AIR CONDITIONER
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Ambient Temp Sensor (Ambi Temp Sens)	Ambient temperature sensor / Min.: -23.3°C (-9.94°F), Max.: 65.95°C (150.71°F)	Actual ambient temperature displayed	-
   Adjusted Ambient Temp (Ambi Temp)	Adjusted ambient temperature / Min.: -30.8°C (-23.44°F), Max.: 50.8°C (123.44°F)	-	-
   Evaporator Fin Thermistor (Evap Fin Temp)	Evaporator fin temperature / Min.: -29.7°C (-21.46°F), Max.: 59.55°C (139.19°F)	Actual evaporator temperature displayed	-
   Engine Coolant Temp (Coolant Temp)	Engine coolant temperature / Min.: 1.3°C (34.34°F), Max.: 90.55°C (194.99°F)	Actual engine coolant temperature displayed while engine is warmed up	-
   Regulator Pressure Sensor (Reg Press Sens)	Regulator pressure sensor / Min.: 0 kgf/cm2 G (-0.45668 MPaG), Max.: 38.25 kgf/cm2 G (3.29437 MPaG)	Actual refrigerant pressure displayed	-
   Regulator Control Current (Reg Ctrl Currnt)	Compressor variable output current / Min.: 0 A, Max.: 0.997 A	-	-
   Electric Heater Count*2 (Heater Count)	Number of electric heaters operating / Min.: 0, Max.: 3	-	-
   Flow Sensor*1 (Flow Sens)	A/C flow sensor / Min.: 0 V, Max.: 5 V	Engine is running A/C switch ON: 3.76 to 4.7 V A/C switch OFF: 0.3 to 3.76 V	A/C flow sensor is malfunctioning when a constant value below 0.3 V or higher than 4.7 V is displayed continuously for more than 4 seconds.
   A/C Cutoff Signal (A/C Cutoff)	A/C control cutoff signal / OFF or ON	A/C switch on: OFF A/C switch off: ON	-
   Number of Trouble Codes (#Codes)	Number of trouble codes / Min.: 0, Max.: 255	Number of DTCs will be displayed	-

   • *1: for TMC Made and except TMC Made 2ZR-FE
   • *2: w/ PTC Heater Assembly

Use the Techstream to perform Active Tests allows the relay, actuator, and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.
5. Check the operation by referring to the table below.
   AIR CONDITIONER
   
   

   Tester Display	Test Part	Control Range	Normal Condition
   Magnetic Clutch Relay (A/C Mag Clutch)	A/C system operation	OFF, ON	-
   Heater Active Level*1 (Heater Level)	Heater active level	Min.: 0, Max.: 3	-

   • *1: w/ PTC Heater Assembly