All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Key / Data List.
5. Read the Data List according to the display on the Techstream.
   SMART KEY (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Auto Entry Cancel SW	Entry function cancel / ON or OFF	Mode status is displayed	-

   Result

   Result	Proceed to
   Entry function is ON	A
   Entry function is OFF	B

A → See step   7 

B: Go to next step 

1. Move the electrical key transmitter as described below and perform the operation inspection.

   HINT: 

   • When the electrical key transmitter is brought near the door outside handle or outside electrical key oscillator, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
   • The transmitting waves of the wireless functions and entry functions are the same, but the wave logic is different. As a result, it is possible that only the wireless functions or only the entry functions are affected by wave interference.
2. Bring the electrical key transmitter near the front RH door outside handle, and perform a front RH door entry lock and unlock operation check.
   Fig 1: Identifying Distance Between Electrical Key Transmitter And Front Passenger Door Outside Handle

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   NOTE:

   If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.

3. Bring the electrical key transmitter near the front LH door outside handle, and perform a front LH door entry lock and unlock operation check.
   Fig 2: Identifying Distance Between Electrical Key Transmitter And Driver Door Outside Handle

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   NOTE:

   If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.

4. Bring the electrical key transmitter near the outside electrical key oscillator (in rear bumper), and perform an entry luggage compartment open function check.
   Fig 3: Identifying Distance Between Electrical Key Transmitter And Outside Electrical Key Oscillator (Luggage Compartment)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   NOTE:

   If the key is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.

   HINT: 

   If the inspection result indicates that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

   Result

   Result	Proceed to
   Some operation checks are normal	A
   All operation checks fail	B

A → AFFECTED BY WAVE INTERFERENCE 

B: Go to next step 

1. Diagnostic mode inspection
   Fig 4: Identifying Distance Between Electrical Key Transmitter And Driver Door Outside Handle

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Driver Side.
   5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
2. Diagnostic mode inspection
   Fig 5: Identifying Distance Between Electrical Key Transmitter And Door Outside Handle

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Passenger Side.
   5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
3. Diagnostic mode inspection
   Fig 6: Identifying Distance Between Key And Vehicle

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Luggage (outside).
   5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
4. Diagnostic mode inspection
   Fig 7: Identifying Key Inspection Point

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Access / Utility / Communication Check (Key Diag Mode) / Overhead + Front Room.
   5. When the electrical key transmitter is placed on the driver seat or front passenger seat cushion, check that the wireless door lock buzzer sounds.
5. Diagnostic mode inspection
   Fig 8: Identifying Key Inspection Point

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Rear Room.
   5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
6. Diagnostic mode inspection
   Fig 9: Identifying Key Lock-In Prevention's Detection Area

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Connect the Techstream to the DLC3.
   2. Turn the engine switch on (IG).
   3. Turn the Techstream on.
   4. Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check (Key Diag Mode) / Overhead + Luggage (inside).
   5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

      Result

      Result	Proceed to
      Some diagnostic mode inspections fail (door)	A
      Some diagnostic mode inspections fail (indoor)	B
      Some diagnostic mode inspections fail (luggage compartment)	C
      All diagnostic mode inspections are normal	D
      All diagnostic mode inspections fail	E

A → GO TO OTHER PROBLEM (PROCEED TO  PROBLEM SYMPTOMS TABLE  PROBLEM SYMPTOM TABLE FOR EACH DOOR) 

B → See step   8 

C → See step   9 

D → See step   10 

E: Go to next step 

1. Replace the electrical key transmitter.

NEXT: Go to next step 

1. Register the electrical key transmitter. Refer to REGISTRATION .

NEXT: Go to next step 

1. Check that the entry functions operate normally.

   OK

   Entry functions operate normally.

NG → See step   11 

OK → END (ELECTRICAL KEY TRANSMITTER IS DEFECTIVE)