LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2012 >> Matrix S, FWD, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 52 (Smart Key System (Keyless Entry) (Diagnostics - Introduction)) >> SMART KEY SYSTEM (for Start Function) >> Data List / Active Test >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

WARNING: This page is about a different car, the 2011 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the Techstream to the DLC3.

      When using the Techstream with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 or less second intervals until communication between the tester and vehicle starts.

    2. Turn the engine switch on (IG).
    3. Read the Data List according to the displays on the Techstream.
      MAIN BODY

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ACC SW Engine switch on (ACC) / ON or OFF ON: Engine switch on (ACC)
      OFF: Engine switch off
      -
      IG SW Engine switch on (IG) / ON or OFF ON: Engine switch on (IG)
      OFF: Engine switch off
      -
      Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
      OFF: Brake pedal released
      -
      Start Switch 1 Start switch 1 / ON or OFF ON: Engine switch is pushed
      OFF: Engine switch is not pushed
      -
      Start Switch 2 Start switch 2 / ON or OFF ON: Engine switch is pushed
      OFF: Engine switch is not pushed
      -
      Steering Unlock Switch Steering lock condition / ON or OFF ON: Steering is unlocked (Engine switch on (ACC))
      OFF: Steering is locked (Engine switch off)
      -
      Neutral SW / Clutch SW Park/Neutral position switch / ON or OFF ON: Shift position is N
      OFF: Shift position is except N
      -
      Shift P Signal Shift P position signal / ON or OFF ON: Shift position is P
      OFF: Shift position is not P
      -
      Vehicle Speed Signal Vehicle speed signal / Stop or Run Stop: Vehicle is stopped
      Run: Vehicle is running
      -
      Engine Condition Engine condition / Stop or Run Stop: Engine is stopped
      Run: Engine is running
      -
      IG1 Relay Monitor (Outside) IG1 relay monitor (outer) / ON or OFF ON: Engine switch on (IG)
      OFF: Engine switch off
      -
      IG2 Relay Monitor (Outside) IG2 relay monitor (outer) / ON or OFF ON: Engine switch on (IG)
      OFF: Engine switch off
      -
      IG1 Relay Monitor (Inside) IG1 relay monitor (inner) / ON or OFF ON: Engine switch on (IG)
      OFF: Engine switch off
      -
      IG2 Relay Monitor (Inside) IG2 relay monitor (inner) / ON or OFF ON: Engine switch on (IG)
      OFF: Engine switch off
      -
      ACC Relay Monitor ACC relay monitor / ON or OFF ON: Engine switch on (ACC)
      OFF: Engine switch off
      -
      Latch Circuit Ratch circuit / ON or OFF ON: Engine switch on (IG) or engine running
      OFF: Engine switch off or on (ACC)
      -
      Starter Request Signal Starter request signal monitor / ON or OFF ON: Starter relay is ON
      OFF: Starter relay is OFF
      Engine switch pressed and held with shift lever in P or N
      Power Supply Condition Power supply condition / All, ACC ON, IG1 IG2, ST ON All: All relays are OFF
      ACC ON: ACC relay is ON
      IG1: IG1 relay is ON
      IG2: IG2 relay is ON
      ST ON: ST request signal is ON
      -
      ACC Relay Cut Signal ACC relay cut signal / ON or OFF ON: Engine is cranking
      OFF: Engine is not cranking
      -
      Starter Relay Monitor STARTER relay monitor / ON or OFF ON: Engine is cranking
      OFF: Engine is not cranking
      Engine is cranking with engine switch on (IG) and shift lever in P or N
      Communication Entry&Start Communication for certification ECU (smart key ECU assembly) / OK or Stop OK: Communication
      Stop: No communication
      -
  2. PERFORM ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Test allows the relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing the Active Test early in troubleshooting is one way to save diagnostic time. The Data List can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Perform the Active Test according to the display on the Techstream.
    MAIN BODY

    Tester Display Test Part Control Range Diagnostic Note
    Indicator for Lighting Indicator for lighting ON / OFF -
    Indicator Condition Engine switch indicator Green / Amber / No Sig -
    P Supply for Steering lock Power supply for steering lock ECU ON / OFF -