Data List / Active Test
- DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Power Source Control / Data List.
- Read the Data List according to the display on the Techstream.POWER SOURCE CONTROL
Tester Display Measurement Item/Range Normal Condition Diagnostic Note Stop Light Switch1 Stop light switch 1/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- Start Switch1 Start switch 1/ON or OFF ON: Power switch pushed
OFF: Power switch not pushed- Start Switch2 Start switch 2/ON or OFF ON: Power switch pushed
OFF: Power switch not pushed- Latch Circuit Latch circuit/ON or OFF ON: Power switch on (IG) or on (READY)
OFF: Power switch off or on (ACC)- IG1 Relay Monitor (Outside) IG1 outer relay monitor/ON or OFF ON: Power switch on (IG)
OFF: Power switch off- IG1 Relay Monitor (Inside) IG1 inner relay monitor/ON or OFF ON: Power switch on (IG)
OFF: Power switch off- IG2 Relay Monitor (Outside) IG2 outer relay monitor/ON or OFF ON: Power switch on (IG)
OFF: Power switch off- IG2 Relay Monitor (Inside) IG2 inner relay monitor/ON or OFF ON: Power switch on (IG)
OFF: Power switch off- Starter Request Signal Starter request signal monitor/ON or OFF ON: ST relay on
OFF: ST relay off- ACC Relay Monitor ACC relay monitor/ON or OFF ON: Power switch on (ACC)
OFF: Power switch off- Ready Signal Status of the ready signal/ON or OFF ON: Hybrid control system on (on (READY))
OFF: Hybrid control system off- Vehicle Speed Signal Vehicle speed signal/Stop or Run Stop: Vehicle stopped
Run: Vehicle running- Shift P Signal Pulse Status of the shift P signal pulse/Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1 Unknown: Other
Error2: Signal abnormal and park (P) selected
Normal2: Signal normal and park (P) selected
Error1: Signal abnormal and park (P) state cannot be determined
Normal3: Signal normal and R, N, D or B selected
Error3: Signal abnormal and R, N, D or B selected
Normal1: Signal normal and park (P) state cannot be determined- Power Supply Condition Power supply condition/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON All OFF: All relays off
ACC ON: ACC relay on
IG1 ON: IG1 relay on
IG2 ON: IG2 relay on
ST ON: ST request signal on- Powertrain Type Status of the powertrain type/HV-AT, Conventional-AT, Conventional-MT, Conventional-MMT HV-AT - IG1 Circuit Status of the IG1 relay activation circuit/OK or NG OK: IG1 relay activation circuit normal
NG: IG1 relay activation circuit abnormal- IG2 Circuit Status of the IG2 relay activation circuit/OK or NG OK: IG2 relay activation circuit normal
NG: IG2 relay activation circuit abnormal- Starter Switch Signal Mismatch Power switch error detection/No or Yes No: Power switch error not detected
Yes: Power switch error detected- Park Signal Mismatch Status of the park signal mismatch/No or Yes No: Park signal mismatch no detected
Yes: Park signal mismatch detected- Key Certification Waiting Timed Out Key certification error detection/No or Yes No: Key certification error not detected
Yes: Key certification error detected- Number of Diagnosis Code Number of diagnosis code/Min.: 0, MAX.: 255 Number of DTCs will be displayed - - Enter the following menus: Body Electrical / Smart Key / Data List.
- Read the Data List according to the display on the Techstream.SMART KEY
Tester Display Measurement Item/Range Normal Condition Diagnostic Note Ignition Switch Power switch/ON or OFF ON: Power switch on (IG)
OFF: Power switch off- Key Low Battery Low key battery/Yes or No Yes: Key battery voltage low
No: Key battery voltage normal- # Code Number of DTC recorded/Min.: 0, Max.: 225 Number of DTCs displayed - Steering Lock Sleep Cond Transmission control ECU sleep condition/Yes or No Yes: Transmission control ECU sleep mode can be entered
No: Transmission control ECU sleep mode cannot be entered- Steering Lock Start Cond Transmission control ECU start signal/Yes or No Yes: Transmission control ECU sent a start signal
No: Transmission control ECU did not send a start signal- Engine Start Condition Hybrid control system start condition/OK or NG OK: Hybrid control system allowed to start
NG: Hybrid control system not allowed to start- Engine Start Request Start request condition signal/OK or NG OK: Start request condition signal received
NG: Start request condition signal not received- 3bit Code Request Status of the 3-bit code request/OK or NG OK: 3-bit code request signal received
NG: 3-bit code request signal not received- S Code Check S code certification result/OK or NG OK: Certification confirmed
NG: Certification not confirmed- L Code Check L code certification result/OK or NG OK: Certification confirmed
NG: Certification not confirmed- Unlock Request Receive Status of the gearshift control unlock request receive/OK or NG OK: Gearshift control unlock request signal received
NG: Gearshift control unlock request signal not received- Lock Request Receive Status of the gearshift control lock request receive/OK or NG OK: Gearshift control lock request signal received
NG: Gearshift control lock request signal not received- S Code Check (Past) S code certification result (Past)/OK or NG OK: Certification confirmed (past)
NG: Certification not confirmed (past)- L Code Check (Past) L code verification result (Past)/OK or NG OK: Certification confirmed (past)
NG: Certification not confirmed (past)- EFI Code Receive SFI communication (when DTC stored)/OK or NG OK: SFI code received
NG: SFI code not received- EFI Communication SFI communication /OK or NG OK: SFI communication normal
NG: SFI communication abnormal- Ignition Available Area Ignition available area/Front or All Customization status displayed -
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relay, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Power Source Control / Active Test.
- Perform the Active Test according to the display on the Techstream.POWER SOURCE CONTROL
Tester Display Test Part Control Range Diagnostic Note Indicator Condition Power switch indicator Green/Red/No Sig Power switch on (READY) - Enter the following menus: Body Electrical / Smart Key/ Active Test.
- Perform the Active Test according to the display on the Techstream.SMART KEY
Tester Display Test Part Control Range Diagnostic Note Power / Engine SW Light Power switch illumination ON/OFF Operate with power switch on (IG) and the vehicle stopped.