Data List / Active Test
WARNING: This page is about a different variant/trim than selected.
- DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Smart Key / Data List.
- Read the Data List according to the display on the Techstream.
SMART KEY (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))Tester Display Measurement Item/Range Normal Condition Diagnostic Note Ignition Switch Power switch on (IG) signal/ON or OFF ON: Power switch on (IG) or hybrid vehicle control system started
OFF: Power switch off- Immobilizer when IG=ON Immobilizer system status when power switch on (IG)l/UNSET or SET SET: Power switch off
UNSET: Power switch on (IG) or hybrid vehicle control system started- Immobilizer Immobilizer system status/Set or Unset Set: Power switch off
Unset: Power switch on (IG) or hybrid vehicle control system started- Master Key Master key code signal/Match or No Match Match: Master key code sent
No Match: Unmatched master key code sent- Sub Key Sub-key (master key) code signal/Match or No Match Match: Sub-key (master key) code sent
No Match: Unmatched sub-key (master key) code sent- BCC Malfunction Transponder chip signal/OK or NG OK: Correct data sent
NG: Incorrect data sent- Abnormal Status Transponder chip data/OK or NG OK: Data OK
NG: Data error- Different Encrypt Code Transponder chip signal/OK or NG OK: Correct data sent
NG: Incorrect data sent- Different Serial Number Transponder chip signal/OK or NG OK: Correct data sent
NG: Incorrect data sent- Frame Error Transponder chip signal/OK or NG OK: Correct data sent
NG: Incorrect data sent- Response Transponder chip signal/OK or NG OK: Correct data sent
NG: Incorrect data sent- Wireless C Code Wireless C Code/No Regd or Regd No Regd: Wireless C Code not registered
Regd: Wireless C Code registered- ID-BOX Sleep Condition Certification ECU (smart key ECU assembly)*1 or ID code box (immobilizer code ECU)*2 condition/Yes or No Yes: Certification ECU (smart key ECU assembly)*1 or ID code box (immobilizer code ECU)*2 in sleep condition
No: Certification ECU (smart key ECU assembly)*1 or ID code box (immobilizer code ECU)*2 not in sleep condition- ID-BOX Start Condition Certification ECU (smart key ECU assembly)*1 or ID code box (immobilizer code ECU)*2 condition/Yes or No Yes: Certification ECU (smart key ECU assembly)*1 or ID code box (immobilizer code ECU)*2 sends wake up signal
No: Certification ECU (smart key ECU assembly)*1 or ID code box (immobilizer code ECU)*2 not send wake up signal- Engine Start Request Certification ECU (smart key ECU assembly)*1 or ID code box (immobilizer code ECU)*2 start request condition/OK or NG OK: Start request condition signal received
NG: Start request condition signal not received- 3bit Code Request 3bit code reception status/OK or NG OK: 3bit code received
NG: 3bit code not receivedS Code Check S code verification result/OK or NG OK: Verification confirmed
NG: Verification not confirmed- L Code Check L code verification result/OK or NG OK: Verification confirmed
NG: Verification not confirmed- Unlock Request Receive Unlock command reception status/OK or NG OK: Unlock request received
NG: Unlock request not received- Lock Request Receive Lock command reception status/OK or NG OK: Lock request received
NG: Lock request not received- S Code Check (Past) S code verification result (past)/OK or NG(Past) OK: Verification confirmed (past)
NG(Past): Verification not confirmed (past)- L Code Check (Past) L code verification result (past)/OK or NG(Past) OK: Verification confirmed (past)
NG(Past): Verification not confirmed (past)- EFI Code Receive HV code receive (when DTC stored)/OK or NG OK: HV code received
NG: HV code not received- EFI Communication HV communication/OK or NG OK: HV communication normal
NG: HV communication abnormal- # Codes Number of trouble codes/Min.: 0 or Max.: 255 Number of DTCs will be displayed - - *1: except Canada
- *2: for Canada
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Smart Key / Active Test.
- Perform the Active Test according to the display on the Techstream.
SMART KEY (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))Tester Display Test Part Control Range Diagnostic Note Immobilizer Indicator Security indicator light ON or OFF -