Data List / Active Test

HINT: 

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Key / Data List.
5. Read the Data List according to the display on the Techstream.
   SMART KEY
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Ignition Switch	Power switch on (IG) signal/ON or OFF	ON: Power switch on (IG) or hybrid control system started OFF: Power switch off	-
   Immobilizer when IG=ON	Immobiliser system status when power switch on (IG)l/UNSET or SET	SET: Immobiliser set UNSET: Immobiliser unset	-
   Immobiliser	Immobiliser system status/Set or Unset	Set: Power switch off Unset: Power switch on (ACC or IG) or hybrid control system started	-
   Master Key	Master key code signal/Match or NoMatch	Match: Master key code sent NoMatch: Unmatched master key code sent	-
   Sub Key	Sub-key (master key) code signal/Match or NoMatch	Match: Sub-key (master key) code sent NoMatch: Unmatched sub-key (master key) code sent	-
   BCC Malfunction	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Abnormal Status	Transponder chip data/OK or NG	OK: Data OK NG: Data error	-
   Different Encrypt Code	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Different Serial Number	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Frame Error	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Response	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Wireless C Code	Wireless C Code/No Regd or Regd	No Regd: Wireless C Code not registered Regd: Wireless C Code registered	-
   ID-BOX Sleep Condition	ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 condition/Yes or No	Yes: ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 in sleep condition No: ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 not in sleep condition	-
   ID-BOX Start Condition	ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 condition/Yes or No	Yes: ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 sends wake up signal No: ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 not send wake up signal	-
   Engine Start Request	ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 start request condition/OK or NG	OK: Start request condition signal received NG: Start request condition signal not received	-
   3bit Code Request	3bit code reception status/OK or NG	OK: 3bit code received NG: 3bit code not received
   S Code Check	S code verification result/OK or NG	OK: Verification confirmed NG: Verification not confirmed	-
   L Code Check	L code verification result/OK or NG	OK: Verification confirmed NG: Verification not confirmed	-
   Unlock Request Receive	Unlock command reception status/OK or NG	OK: Unlock request received NG: Unlock request not received	-
   Lock Request Receive	Lock command reception status/OK or NG	OK: Lock request received NG: Lock request not received	-
   S Code Check (Past)	S code verification result (past)/OK or NG(Past)	OK: Verification confirmed (past) NG(Past): Verification not confirmed (past)	-
   L Code Check (Past)	L code verification result (past)/OK or NG(Past)	OK: Verification confirmed (past) NG(Past): Verification not confirmed (past)	-
   EFI Code Receive	HV code receive (when DTC stored)/OK or NG	OK: HV code received NG: HV code not received	-
   EFI Communication	HV communication/OK or NG	OK: HV communication normal NG: HV communication abnormal	-
   # Codes	Number of trouble codes/Min.: 0 or Max.: 255	Number of DTCs will be displayed	-

   • *1: for Canada
   • *2: except Canada

HINT: 

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Key / Active Test.
5. Perform the Active Test according to the display on the Techstream.
   SMART KEY
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Immobiliser Indicator	Security indicator light	ON or OFF	-