Operation Check

CHECK PANEL & STEERING SWITCH

HINT:

The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode. Refer to DTC CHECK / CLEAR .
Select "Function Check/Setting" from the "Service Menu" screen.

Fig 1: identifying Screen Display - Function Check/Setting
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.

Fig 2: Identifying Screen Display - Panel & Steering Switch
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Panel & Steering Switch Check Mode

Fig 3: Identifying Screen Display - Panel & Steering Switch Check Mode

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

SCREEN DESCRIPTION

Display	Content
*a: Switch condition	"Pushed" is displayed when any switch is pushed
*b: Number of switches pushed	Number of switches pushed at once is displayed If more than 3 switches are pushed at once, "More than 3" is displayed
*c: Rotary switch direction	Direction of rotary switch is displayed

Operate each switch and check that the switch conditions are correctly displayed.
NOTE:
When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

CHECK TOUCH SWITCH
HINT:
- The touch switches on the screen are checked in the following procedure.
- Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
1. Enter diagnostic mode. Refer to DTC CHECK / CLEAR .
2. Select "Function Check/Setting" from the "Service Menu" screen.
  
  Fig 4: identifying Screen Display - Function Check/Setting
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Select "Touch Switch" from the "Function Check/Setting I" screen.
  
  Fig 5: identifying Screen Display - Touch Switch
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Touch Switch Check
  
  Fig 6: Identifying Screen Display - Touch Switch Check
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.
    HINT:
    - A "+" mark is displayed where the display is touched.
    - The "+" mark remains on the display even after the finger is removed.

CHECK MICROPHONE & VOICE RECOGNITION

HINT:

The microphone and microphone input level are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode. Refer to DTC CHECK / CLEAR .
Select "Function Check/Setting" from the "Service Menu" screen.

Fig 7: identifying Screen Display - Function Check/Setting
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Select "Mic & Voice Recognition" from the "Function Check/Setting I" screen.

Fig 8: Identifying Screen Display - Mic & Voice Recognition
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Microphone & Voice Recognition Check

Fig 9: Identifying Screen Display - Microphone & Voice Recognition Check

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

SCREEN DESCRIPTION

Display	Content
*a: Microphone input level meter	Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.
HINT:

The microphone is active at all times when this screen is displayed.

CHECK COLOR BAR
HINT:
- The display color on the screen is checked in the following procedure.
- Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
1. Enter diagnostic mode. Refer to DTC CHECK / CLEAR .
2. Select "Function Check/Setting" from the "Service Menu" screen.
  
  Fig 10: identifying Screen Display - Function Check/Setting
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Select "Color Bar" from the "Function Check/Setting I" screen.
  
  Fig 11: Identifying Screen Display - Color Bar
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Color Bar Check Mode
  
  Fig 12: Identifying Color Bar Check Mode Screen
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. Select a color bar from the "Color Bar Check Mode" screen.
  2. Check the display color.
    HINT:
    - The entire screen turns to the color or stripe selected.
    - Touching the display will return to the "Color Bar Check Mode" screen.

CHECK VEHICLE SIGNAL

HINT:

Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode. Refer to DTC CHECK / CLEAR .
Select "Function Check/Setting" from the "Service Menu" screen.

Fig 13: identifying Screen Display - Function Check/Setting
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Select "Vehicle Signal" from the "Function Check/Setting I" screen.

Fig 14: Identifying Screen Display - Vehicle Signal
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Vehicle Signal Check Mode

Fig 15: Identifying Vehicle Signal Check Mode Screen

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

SCREEN DESCRIPTION

Display	Content
Battery	Battery voltage is displayed.
IG	Ignition switch ON/OFF state is displayed.
PKB	Parking brake ON/OFF state is displayed.
REV	Reverse signal ON/OFF state is displayed.
SPEED	Vehicle speed is displayed in km/h.
TAIL	Tail signal (Light control switch) ON/OFF state is displayed.

HINT:

Only items sending vehicle signals will be displayed.
This screen displays vehicle signals input to the radio and display receiver assembly.
This screen is updated once per second when vehicle input signals change.

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING

HINT:

The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode. Refer to DTC CHECK / CLEAR .
Select "Function Check/Setting" from the "Service Menu" screen.

Fig 16: identifying Screen Display - Function Check/Setting
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

Fig 17: Identifying Screen Display - HF Voice Quality Setting
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)

Fig 18: Identifying Screen Display - Hands-Free Voice Quality Setting

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

SCREEN DESCRIPTION

Display	Content
*a: Receive voice level adjustment	Setting for the voice level received from "Bluetooth" compatible phones.
*b: Send voice level adjustment	Setting for the voice level sent from "Bluetooth" compatible phones.

NOTE:

Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.

If the voice level is low, press the up button, and if the voice level is loud, press the down button.
HINT:
- Each voice level setting is reflected when going back to the normal mode.
- The voice level adjustment ranges from -5 to +5 (for Pioneer, Panasonic or w/o HD Radio for FUJITSU TEN).
- The "Receive Voice Level" adjustment ranges from -5 to 0 (w/ HD Radio for FUJITSU TEN).
- The "Send Voice Level" adjustment ranges from -5 to +2 (w/ HD Radio for FUJITSU TEN).
- The initial level is "0".

Hands-Free Voice Quality (Voice Quality Type adjustment)

Fig 19: Identifying Screen Display - Hands-Free Voice Quality Setting

TEXT IN ILLUSTRATION

*a	Numeric keypad
*b	Setting button
*c	Reset button

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

SETTING

Parameter	Target Phenomenon	Voice Quality Type (FUJITSU TEN)	Voice Quality Type (Panasonic)	Voice Quality Type (Pioneer)	Positive Effect of Changing Voice Quality	Negative Effect of Changing Voice Quality
Echo	The other party hears a lot of echo when speaking to you.	1000 2000	0001	0001 0002 0003 0004 0005	The amount of echo the other party hears of their own voice is reduced.	When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc.
Half Duplex	When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc.	0100 0200	0002	0010 0020 0030 0040 0050	When both parties speak at the same time, the phenomenon by which the other party's voice suddenly drops in volume, cuts out etc. reduces.	The amount of echo the other party hears of their own voice increases.
Noise	The other party hears a lot of vehicle noise etc. when listening to your voice.	0010 0020	-	0100 0200 0300 0400 0500	The amount of vehicle noise etc. the other party hears when listening to your voice reduces.	The quality of your voice, that the other party hears, reduces.
Voice Quality	The quality of your voice, that the other party hears, is low.	0001 0002	0003	1000 2000 3000 4000 5000	The quality of your voice, that the other party hears, increases.	The amount of noise etc. the other party hears when listening to your voice increases.

HINT:

Refer to the "Unit Version Information" screen to confirm radio and display receiver assembly manufacturer information.
The type of adjustments that can be made using voice quality type adjustment only adjust the sound quality of your voice that the other party hears. It cannot adjust the sound quality of the other party's voice that you hear.
The default value is "0000".
Settings will be applied when the normal screen is returned to.
When multiple setting values are available, the higher the setting value, the bigger the effect. However, as the positive effects increase, so do the negative effects.
If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.

CHECK UNIT VERSION INFORMATION

HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

Enter diagnostic mode. Refer to DTC CHECK / CLEAR .
Select "Service Information" from the "Service Menu" screen.

Fig 20: Identifying Screen Display - Service Information
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Select "Version Information" from the "Service Information" screen.

Fig 21: Identifying Screen Display - Version Information
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Unit Version Information

Fig 23: Identifying Screen Display - Unit Version Information

SCREEN DESCRIPTION

Display	Content
*a: Device name	Target device
*b: Manufacturer name	Manufacturer of the ECU (target device)
*c: Component name	Component name of the ECU (target device)
*d: Version	Version of the ECU (target device)

HINT:

Depending on the manufacturer, some component names and versions will be displayed differently.