LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2013 >> Matrix Base, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 38 (Active Torque Control 4WD System (Diagnostics - Introduction)) >> Active Torque Control 4WD System >> Data List / Active Test >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

WARNING: This page is about a different variant/trim than selected.
  1. DATA LIST 

    HINT: 

    Using the Techstream Data List allows sensor and other item values to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Chassis / 4WD / Data List.
    7. According to the display on the Techstream, read the Data List.
    4WD CONTROL ECU

    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    4WD WARN LIGHT 4WD warning light /OFF or ON OFF: 4WD warning light OFF
    ON: 4WD warning light ON    		 -
    STOP LIGHT SW Stop light switch /OFF or ON OFF: Brake pedal released
    ON: Brake pedal depressed    		 -
    FR WHEEL SPD FR wheel speed /
    Min.: 0 km/h (0 mph)
    Reading : Max.: 326.4 km/h (202.8 mph)    		 Actual wheel speed Almost no difference from the speedometer
    FL WHEEL SPD FL wheel speed /
    Min.: 0 km/h (0 mph)
    Reading : Max.: 326.4 km/h (202.8 mph)    		 Actual wheel speed Almost no difference from the speedometer
    RR WHEEL SPD RR wheel speed /
    Min.: 0 km/h (0 mph)
    Reading : Max.: 326.4 km/h (202.8 mph)    		 Actual wheel speed Almost no difference from the speedometer
    RLWHEEL SPD RL wheel speed /
    Min.: 0 km/h (0 mph)
    Reading : Max.: 326.4 km/h (202.8 mph)    		 Actual wheel speed Almost no difference from the speedometer
    SLC CUR SLC solenoid (4WD linear solenoid) current /
    Min.: 0 A
    Max.: 3 A    		 Min.: 0 A
    Max.: 3 A    		 -
    Forward and Rearward G Forward and Rearward G /
    Min.: -25.10 m/s2
    Max.: 24.90 m/s2    		 Approximately 0 +/-0.13 while stationary -
  2. ACTIVE TEST 

    HINT: 

    Performing the Techstream Active Test allows switch and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Chassis / 4WD / Active Test.
    7. According to the display on the Techstream, perform the Active Test.
      CHASSIS / 4WD / ACTIVE TEST

      Tester Display Test Part Control Range Diagnostic Note
      4WD Light 4WD Warning Light Warning light is ON/OFF Observer combination meter
scientia non olet · About LEMON Manuals