LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2013 >> Prius Plug-in >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 74 (Cruise Control System (Diagnostics - Introduction) (Except Plug-In)) >> Cruise Control System >> Data List / Active Test >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

WARNING: This page is about a different variant/trim than selected.
  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Cruise Control / Data List.
    5. According to the display on the Techstream, read the Data List.
      CRUISE CONTROL (POWER MANAGEMENT CONTROL ECU)

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      CCS Vehicle Spd Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph) Actual vehicle speed is displayed -
      CCS Mem Vehicle Spd Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph) Actual vehicle speed stored in memory -
      Cruise Control Cruise control / ON or OFF ON: Cruise control activated
      OFF: Cruise control deactivated      		 -
      Main SW M-CPU Cruise control switch (M-CPU) / ON or OFF ON: Cruise main switch on
      OFF: Cruise main switch off      		 -
      CCS Ready M-CPU Cruise control system standby condition (M-CPU) / ON or OFF Each time main switch is pushed, ON/OFF changes -
      CCS Indicator M-CPU Cruise main indicator (M-CPU) / ON or OFF ON: Cruise main indicator light on
      OFF: Cruise main indicator light off      		 -
      Cancel Switch CANCEL switch / ON or OFF ON: CANCEL switch on
      OFF: CANCEL switch off      		 -
      SET/COAST Switch - SET switch / ON or OFF ON: - SET switch on
      OFF: - SET switch off      		 -
      RES/ACC Switch + RES switch / ON or OFF ON: + RES switch on
      OFF: + RES switch off      		 -
      Stop Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
      OFF: Brake pedal released      		 -
      Cruise Operation Status Shift position signal (D position) / ON or OFF ON: Shift lever in D
      OFF: Shift lever not in D      		 -
      Cruise Request Driving Force Cruise control driving force signal / min.: -51.2 kN, max.: 51.2 kN Actual driving force -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
    5. According to the display on the Techstream, perform the "Active Test".
      COMBINATION METER

      Tester Display Test Part Control Range Diagnostic Note
      Indicat. Lamp Cruise Cruise main indicator light ON / OFF -
      Indicat. SET SET indicator light BLINK / OFF -
scientia non olet · About LEMON Manuals