LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2013 >> Prius Two >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 85 (Dynamic Radar Cruise Control System (Diagnostic Codes & Circuit Tests) (Plug-In)) >> Dynamic Radar Cruise Control System >> DTC C1A50: Brake System >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC C1A50: Brake System: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
    5. Check for DTCs.

      Result

      Result Proceed to
      DTC is not output A
      DTC is output B

    B → See step   8 

    A: Go to next step 

  2. CHECK FOR DTCs (DTC C1A50) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Clear the DTCs. Refer to DTC CHECK / CLEAR .
    4. Perform the following to make sure that the DTC detection conditions are met.

      HINT: 

      If the detection conditions are not met, the malfunction cannot be detected.

      1. Drive the vehicle at a speed for which radar cruise control operation is possible.
      2. Turn the cruise control system on using the cruise control switch (ON-OFF button).
      3. Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
    5. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
    6. Check for DTCs.

      Result

      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

    B → See step   3 

    A → See step   9 

  3. REPLACE DRIVING SUPPORT ECU ASSEMBLY 
    1. Replace the driving support ECU assembly. Refer to REMOVAL .

    NEXT: Go to next step 

  4. CHECK FOR DTCs (DTC C1A50) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Clear the DTCs. Refer to DTC CHECK / CLEAR .
    4. Perform the following to make sure that the DTC detection conditions are met.

      HINT: 

      If the detection conditions are not met, the malfunction cannot be detected.

      1. Drive the vehicle at a speed for which radar cruise control operation is possible.
      2. Turn the cruise control system on using the cruise control switch (ON-OFF button).
      3. Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
    5. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
    6. Check for DTCs.

      Result

      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

    B → See step   5 

    A → END 

  5. REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 
    1. Replace the brake booster with master cylinder assembly (skid control ECU). Refer to REMOVAL .

    NEXT: Go to next step 

  6. CHECK FOR DTCs (DTC C1A50) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Clear the DTCs. Refer to DTC CHECK / CLEAR .
    4. Perform the following to make sure that the DTC detection conditions are met.

      HINT: 

      If the detection conditions are not met, the malfunction cannot be detected.

      1. Drive the vehicle at a speed for which radar cruise control operation is possible.
      2. Turn the cruise control system on using the cruise control switch (ON-OFF button).
      3. Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.
    5. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
    6. Check for DTCs.

      Result

      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

    B → See step   7 

    A → END 

  7. REPLACE POWER MANAGEMENT CONTROL ECU. Refer to  REMOVAL 
  8. GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING 
  9. USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING 
scientia non olet · About LEMON Manuals