LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2014 >> Avalon XLE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 15 (Front Power Seat Control System (W/ Memory) (Diagnostics - Introduction) (Hybrid)) >> FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) >> Data List / Active Test [10/2013 - ] >> Data List / Active Test [10/2013 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test [10/2013 - ]

WARNING: This page is about a different variant/trim than selected.
  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Mirror L / Data List.
    5. Read the Data List according to the display on the Techstream.
      MIRROR L

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Seat Memory Switch1 M1 switch / ON or OFF ON: M1 switch on
      OFF: M1 switch off      		 -
      Seat Memory Switch2 M2 switch / ON or OFF ON: M2 switch on
      OFF: M2 switch off      		 -
      Seat Memory Switch3* M3 switch / ON or OFF ON: M3 switch on
      OFF: M3 switch off      		 Not applicable
      Seat Memory Set SW SET switch / ON or OFF ON: SET switch on
      OFF: SET switch off      		 -
      +B Voltage Input Value Power supply for outer mirror control ECU assembly / MIN: 0 V, MAX: 19.98 V Within range from 11 to 14 V -
      • *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
    6. Enter the following menus: Body Electrical / Driver Seat / Data List.
    7. Read the Data List according to the display on the Techstream.
      DRIVER SEAT

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Reclining Rear Reclining switch signal (Rearward) / ON or OFF ON: Reclining switch (Rearward) on
      OFF: Reclining switch (Rearward) off      		 -
      Reclining Front Reclining switch signal (Forward) / ON or OFF ON: Reclining switch (Forward) on
      OFF: Reclining switch (Forward) off      		 -
      Front Vertical Down Front vertical switch signal (Downward) / ON or OFF ON: Front vertical switch (Downward) on
      OFF: Front vertical switch (Downward) off      		 -
      Front Vertical Up Front vertical switch signal (Upward) / ON or OFF ON: Front vertical switch (Upward) on
      OFF: Front vertical switch (Upward) off      		 -
      Lifter Switch Down Lifter switch signal (Downward) / ON or OFF ON: Lifter switch (Downward) on
      OFF: Lifter switch (Downward) off      		 -
      Lifter Switch Up Lifter switch signal (Upward) / ON or OFF ON: Lifter switch (Upward) on
      OFF: Lifter switch (Upward) off      		 -
      Slide Rear Slide switch signal (Rearward) / ON or OFF ON: Slide switch (Rearward) on
      OFF: Slide switch (Rearward) off      		 -
      Slide Front Slide switch signal (Forward) / ON or OFF ON: Slide switch (Forward) on
      OFF: Slide switch (Forward) off      		 -
      Seat Memory No1 Seat position memorized with M1 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 -
      Seat Memory No2 Seat position memorized with M2 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 -
      Seat Memory No3* Seat position memorized with M3 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 Not applicable
      Seat Memory Drv1* Driver seat position memorized with M1 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 Not applicable
      Seat Memory Drv2* Driver seat position memorized with M2 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 Not applicable
      Seat Memory Drv3* Driver seat position memorized with M3 switch / Mem or Not Mem Mem: Memorized
      Not Mem: Not memorized      		 Not applicable
      Ignition Switch Communication state of power switch signal / ON or OFF ON: Power switch on (IG) signal received
      OFF: Power switch off signal not received      		 -
      P Switch* Park state signal / ON or OFF ON: Shift lever in P
      OFF: Shift lever in a position other than P      		 Not applicable
      Parking Brake SW Parking brake switch status / ON or OFF ON: Parking brake applied
      OFF: Parking brake released      		 -
      Vehicle Speed Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed -
      Power Voltage Power supply for front power seat switch LH / min: 0.95 V, max: 20.84 V Within range from 11 V to 14 V -
      Slide Position Seat sliding position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Reclining Position Seat reclining position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Front Vertical Position Seat front vertical position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Lifter Position Seat lifter position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Slide Pos Mem No1 Seat slide position memorized with M1 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Reclining Pos Mem No1 Seat reclining position memorized with M1 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Frnt Vrtcl Pos Mem No1 Front vertical position memorized with M1 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Lifter Pos Mem No1 Lifter position memorized with M1 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Slide Pos Mem No2 Seat slide position memorized with M2 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Reclining Pos Mem No2 Seat reclining position memorized with M2 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Frnt Vrtcl Pos Mem No2 Front vertical position memorized with M2 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Lifter Pos Mem No2 Lifter position memorized with M2 switch / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Slide Pos Mem No3* Seat slide position memorized with M3 switch / min: 0000, max: 65535 Within range from 0000 to 65535 Not applicable
      Reclining Pos Mem No3* Seat reclining position memorized with M3 switch / min: 0000, max: 65535 Within range from 0000 to 65535 Not applicable
      Frnt Vrtcl Pos Mem No3* Front vertical position memorized with M3 switch / min: 0000, max: 65535 Within range from 0000 to 65535 Not applicable
      Lifter Pos Mem No3* Lifter position memorized with M3 switch / min: 0000, max: 65535 Within range from 0000 to 65535 Not applicable
      Motor Status State of slide motor control / STANDBY, MOVING, LOCK STANDBY: Slide motor idle
      MOVING: Slide motor moving
      LOCK: Slide motor locked      		 -
      Slide Position Init Flag Seat slide limit position memory / ON or OFF ON: Memorized
      OFF: Not memorized      		 -
      Slide Position Rear Limit Seat slide position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Shift P sw (PMN) Park state signal / ON or OFF ON: Shift lever in P
      OFF: Shift lever in a position other than P      		 -
      Memory Button Buzzer Request Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT OFF: Buzzer does not sound
      MOVE: Request to sound buzzer when starting memory replay
      REGISTRY: Request to sound buzzer when starting memory registration
      CANCEL: Request to sound buzzer when canceling memory call registration
      REG NG: Request to sound buzzer when memory call registration not possible
      REG WAIT: Request to sound buzzer when starting memory call cabin scan      		 -
      Driver Seat Request Command Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET OFF: No instruction
      MEMORY: Request to memorize
      MEM MOV: Request to recall memory
      MEM SOD: Request to replay
      RET MOV: Request to return
      AWY MOV: Request to move away
      AWY SOD: Request to recall away position memory
      MEM AWY: Request to recall memorized position of seatback
      MEM RET: Request to restore seatback to memorized position      		 -
      Driver Seat POS REQ Seat memory switch operation value / OFF, MEM1, MEM2, MEM3*, DRV1*, DRV2* or DRV3* OFF: No operation
      MEM1: M1 switch operation status
      MEM2: M2 switch operation status
      MEM3: M3 switch operation status*
      DRV1: Other 1 operation status*
      DRV2: Other 2 operation status*
      DRV3: Other 3 operation status*      		 -
      Away Move Range Scale The seat travel distance for the power easy access system / NONE, SMALL, STANDARD or LONG NONE: Seat travel distance none
      SMALL: Seat travel distance short
      STANDARD: Seat travel distance normal
      LONG: Seat travel distance long      		 -
      Return Move Return function / NOT AVL or AVAIL NOT AVL: Not available
      AVAIL: Available      		 -
      Return & Away Function Return & away function / NOT AVL or AVAIL NOT AVL: Not available
      AVAIL: Available      		 -
      Driver Seat Buckle SW Driver seat belt buckle switch / OFF or ON OFF: Driver seat belt unfastened
      ON: Driver seat belt fastened      		 -
      Return Position Return position / min: 0000, max: 65535 Within range from 0000 to 65535 -
      Number of Trouble Codes Number of trouble codes / min.: 0 or max.: 255 Number of DTCs will be displayed -
      • *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
    8. Enter the following menus: Body Electrical / Main Body / Data List.
    9. Read the Data List according to the display on the Techstream.
      MAIN BODY

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal / ON or OFF ON: Lock side of door control switch (power window regulator master switch assembly) pushed
      OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed      		 -
      Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal / ON or OFF ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
      OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed      		 -
      FL Door Courtesy SW Front door courtesy light switch assembly signal / ON or OFF ON: Driver door open
      OFF: Driver door closed      		 -
      Mem SW No. w/KeyID1 Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID1
      MEM SW1: M1 switch linked with key ID1
      MEM SW2: M2 switch linked with key ID1
      MEM SW3: M3 switch linked with key ID1*      		 -
      Mem SW No. w/KeyID2 Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID2
      MEM SW1: M1 switch linked with key ID2
      MEM SW2: M2 switch linked with key ID2
      MEM SW3: M3 switch linked with key ID2*      		 -
      Mem SW No. w/KeyID3 Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID3
      MEM SW1: M1 switch linked with key ID3
      MEM SW2: M2 switch linked with key ID3
      MEM SW3: M3 switch linked with key ID3*      		 -
      Mem SW No. w/KeyID4 Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID4
      MEM SW1: M1 switch linked with key ID4
      MEM SW2: M2 switch linked with key ID4
      MEM SW3: M3 switch linked with key ID4*      		 -
      Mem SW No. w/KeyID5 Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID5
      MEM SW1: M1 switch linked with key ID5
      MEM SW2: M2 switch linked with key ID5
      MEM SW3: M3 switch linked with key ID5*      		 -
      Mem SW No. w/KeyID6 Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID6
      MEM SW1: M1 switch linked with key ID6
      MEM SW2: M2 switch linked with key ID6
      MEM SW3: M3 switch linked with key ID6*      		 -
      Mem SW No. w/KeyID7 Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID7
      MEM SW1: M1 switch linked with key ID7
      MEM SW2: M2 switch linked with key ID7
      MEM SW3: M3 switch linked with key ID7*      		 -
      Driver Seat Memory1 Seat position memorized with M1 switch / OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Driver Seat Memory2 Seat position memorized with M2 switch / OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Driver Seat Memory3* Seat position memorized with M3 switch / OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      • *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Driver Seat / Active Test.
    5. Perform the Active Test according to the display on the Techstream.
      DRIVER SEAT

      Tester Display Test Part Control Range Diagnostic Note
      Seat Reclining Seat reclining operation OFF/Rear/Front -
      Front Vertical Operation Seat front vertical operation OFF/Down/Up -
      Lifter Operation Seat lifter operation OFF/Down/Up -
      Seat Slide Operation Seat slide operation OFF/Rear/Front -
      Buzzer Buzzer operation OFF/ON -
scientia non olet · About LEMON Manuals