LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2014 >> Corolla L, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 7 (Continuously Variable Transaxle (Service Information) (Model Code: ZRE172)) >> Shift Lever >> Reassembly [08/2013 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Reassembly [08/2013 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. HOW TO PREVENT STATIC ELECTRICITY 
    NOTE:
    • Be sure to touch a grounded metal surface with your bare hands to discharge any static electricity before removing or installing the transmission floor shift assembly.
    • Do not touch the electronic components of a circuit board.
    • Keep clothes away from electronic components.
    • Place electronic components removed from the transmission floor shift assembly on SST (anti-static mat).
    1. Wear SST (wrist band).
      GTY477356Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09890-47010 
    2. Connect the ground clip of SST (anti-static mat) securely to a ground point provided in the workshop or on a workbench (anchor bolt).
      • SST: 09890-47010 

      HINT: 

      If the ground clip cable is too short, use an extension cable.

    3. Connect the ground clip of the antistatic wrist strap securely to the specified point of the antistatic mat.
  2. INSTALL LOWER POSITION INDICATOR HOUSING 
    1. Engage the 5 claws to install the lower position indicator housing to the shift lock control unit assembly.
      GTY474606Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL INDICATOR LIGHT WIRE SUB-ASSEMBLY (w/o Sport Sequential Shiftmatic) 
    1. Connect terminals 4, 5, 6, 7, 8, 9, 10, 13, and 14 to the transmission control switch connector as shown in the illustration.
      GTY479767Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Rear view of wire harness connector
      (Transmission Control Switch Connector)
      Indicator Light Wire Sub-assembly Terminal
      NOTE:

      Reconnect each terminal to its original position.

    2. Lock the secondary lock.
      GTY472367Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Secondary Lock
    3. Engage the claw to install the clamp to the transmission control switch connector.
      GTY474607Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Engage the clamp to install the indicator light wire sub-assembly to the shift lock control unit assembly.
      GTY479228Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Guide
      *b Clamp
    5. Engage the guide.
  4. INSTALL INDICATOR LIGHT WIRE SUB-ASSEMBLY (w/ Sport Sequential Shiftmatic) 
    1. Engage the claw to install the clamp to the indicator light wire sub-assembly.
      GTY474605Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Engage the clamp to install the indicator light wire sub-assembly to the shift lock control unit assembly.
      GTY474951Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Guide
      *b Clamp
    3. Engage the guide.
  5. INSTALL SHIFT POSITION INDICATOR 
    1. When replacing the shift position indicator with a new one:
      1. Cut off the top portion of the antistatic bag while retaining enough of the bag to cover a hand.
        GTY474576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. While holding the sides of the shift position indicator through the antistatic bag, turn the bag inside out.
        GTY474577Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Engage the 2 guides to install the shift position indicator to the lower position indicator housing.
        NOTE:
        • While holding the sides of the shift position indicator through the antistatic bag, install it to the lower position indicator housing.
        • Do not damage the shift position indicator.
        GTY474597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. When reusing the shift position indicator:
      1. Engage the 2 guides to install the shift position indicator to the lower position indicator housing.
        NOTE:
        • While holding the sides of the shift position indicator, install it to the lower position indicator housing.
        • Do not damage the shift position indicator.
        GTY474597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect the indicator light wire sub-assembly connector.
      GTY481472Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL POSITION INDICATOR LIGHT GUIDE 
    1. Engage the 5 claws to install the position indicator light guide to the floor shift position indicator housing sub-assembly.
      GTY474598Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not damage the position indicator light guide.

  7. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY 
    1. Engage the 3 claws to install the shifting hole cover sub-assembly to the floor shift position indicator housing sub-assembly.
      GTY474599Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY 
    1. Engage the 4 claws to install the floor shift position indicator housing sub-assembly to the lower position indicator housing.
      GTY474600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      After installation, check that each indicator light illuminates correctly at each shift position.

scientia non olet · About LEMON Manuals