Initialization [10/2013 - ]

WARNING: This page is about a different variant/trim than selected.

PROCEDURES NECESSARY WHEN AUXILIARY BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed	See
Unlock back door	Back door opener	Refer to INITIALIZATION [10/2013 - ]

NOTE:

After the power switch is turned off, the navigation receiver assembly (for Navigation Receiver Type) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Replacement Part	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	See
Throttle body assembly Cleaning the deposits from the throttle body assembly Cylinder head sub-assembly Camshaft (for intake or exhaust camshaft) Camshaft timing gear assembly Piston or piston ring Mass air flow meter sub-assembly Fuel injector assembly Fuel pump Air fuel ratio sensor Heated oxygen sensor Engine coolant temperature sensor Spark plug Ignition coil assembly EGR valve assembly Air leaks from intake system Gas leaks from exhaust system Knock control sensor	Inspection after repair	Poor idle, etc. Engine start function, etc.	Refer to INITIALIZATION [10/2013 - ]
ECM	Vehicle Identification Number (VIN) registration	MIL comes on	Refer to REGISTRATION [10/2013 - ]
Power management control ECU	Code registration (Engine immobilizer system)	Hybrid control system start	Refer to REGISTRATION [10/2013 - ]
Power management control ECU	Current sensor offset learning	Hybrid system warning light illumination	Refer to INSTALLATION [10/2013 - ] - Step 34
Hybrid battery junction block assembly	Current sensor offset learning	Hybrid system warning light illumination	Refer to INSTALLATION [10/2013 - ] - Step 34
HV battery	Recovery inspection	-	Refer to RECOVERY INSPECTION [10/2013 - ]
HV battery	Battery diagnosis Battery status info update	HV battery status information cannot be updated and the previous status continues to be shown	Refer to UTILITY [10/2013 - ]
Hybrid vehicle supply stack sub-assembly	Recovery inspection	-	Refer to RECOVERY INSPECTION [10/2013 - ]
	Battery diagnosis	Cannot identify the stack to be replaced	Refer to UTILITY [10/2013 - ]
	Normal battery stack average voltage calculation	Cannot specify the product number of the stack to be replaced
	Battery status info update	HV battery status information cannot be updated and the previous status continues to be shown
Millimeter wave radar sensor assembly	Adjust millimeter wave radar sensor assembly	Dynamic radar cruise control system Pre-collision system	Refer to ADJUSTMENT [10/2013 - ]
Tire pressure warning ECU Tire pressure warning valve and transmitter	Transmitter ID registration Initialization	When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates. Tire pressure warning function	Refer to REGISTRATION [10/2013 - ] for Registration Refer to INITIALIZATION [10/2013 - ] for Initialization
Brake booster with master cylinder	Initialization and calibration of the linear solenoid valve Yaw rate and acceleration sensor zero point calibration	ABS warning light illumination Brake warning light/yellow (minor malfunction) illumination Slip indicator light illumination VSC disable or malfunctioning	Refer to INITIALIZATION [10/2013 - ] for Initialization Refer to CALIBRATION [10/2013 - ] for Calibration
Brake pedal stroke sensor Brake pedal	Clearing stored linear solenoid valve calibration data Initialization and calibration of the linear solenoid valve		Refer to INITIALIZATION [10/2013 - ]
Yaw rate and acceleration sensor	Clearing zero point calibration data Yaw rate and acceleration sensor zero point calibration		Refer to CALIBRATION [10/2013 - ]
Power steering ECU assembly	Torque sensor zero point calibration Assist map writing	P/S warning light comes on EPS control	Refer to CALIBRATION [10/2013 - ]
Steering post assembly	Torque sensor zero point calibration	Steering effort is different between turning steering wheel to left and right	Refer to CALIBRATION [10/2013 - ]
Inner rear view mirror assembly Garage door opener transmitter	Re-registration of codes in the garage door opener system Register transmitter code Rolling code systems	Garage door opener system	Refer to REGISTRATION [10/2013 - ]
DCM (Telematics Transceiver)	DCM activation	Safety connect system	Refer to DCM ACTIVATION [10/2013 - ]
Certification ECU (smart key ECU assembly) Transmission control ECU assembly ID code box (immobilizer code ECU)*1 Electrical key transmitter sub-assembly	Code registration (Engine immobilizer system)	Wireless door lock control system Smart Key system2 Push-button start3 Hybrid control system start	Refer to REGISTRATION [10/2013 - ]
Occupant detection ECU Front passenger seat	Zero point calibration Sensitivity check	Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger)	Refer to INITIALIZATION [10/2013 - ]
Door window regulator assembly Power window regulator motor assembly Door glass Door glass run	Initialize power window control system	Auto up/down function Jam protection function Operation function after power switch is turned off	Refer to INITIALIZATION [10/2013 - ]
Headlight leveling ECU assembly Rear height control sensor sub-assembly	Perform Headlight leveling ECU initialization	Automatic headlight beam level control function	Refer to INITIALIZATION [10/2013 - ]

*1: for Canada
*2: w/ Smart Key System (for Entry Function)
*3: w/o Smart Key System (for Entry Function)