LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2014 >> Prius Two >> Repair and Diagnosis (Single Page) >> External Pages >> Different variant/trim >> Section 100 (Brake Control System (Service Information) (Plug-In)) >> Yaw Rate And Acceleration Sensor >> Installation [10/2013 - ] >> Installation [10/2013 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Installation [10/2013 - ]

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL YAW RATE AND ACCELERATION SENSOR 
    1. Connect the yaw rate and acceleration sensor connector.
      Fig 1: Identifying Yaw Rate & Acceleration Sensor Connector & Bolts
      GTY217207Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Make sure that the yaw rate and acceleration sensor connector is connected securely.

    2. Install the yaw rate and acceleration sensor with the 2 bolts.

      Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

      NOTE:
      • Do not damage the yaw rate and acceleration sensor.
      • Make sure that the yaw rate and acceleration sensor is installed securely.
      • Do not use dropped or damaged parts.
      • Keep the contact surfaces of the yaw rate and acceleration sensor and the body free of foreign matter.
      • Make sure that the sensor is facing the correct direction.
  2. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY  . Refer to INSTALLATION [10/2013 - ] - Step 19
  3. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY  . Refer to INSTALLATION [10/2013 - ] - Step 1
  4. INSTALL AIR CONDITIONING CONTROL ASSEMBLY  . Refer to INSTALLATION [10/2013 - ] - Step 1
  5. INSTALL CONSOLE BOX ASSEMBLY  . Refer to INSTALLATION [10/2013 - ] - Step 22
  6. INSTALL BOX BOTTOM MAT  . Refer to INSTALLATION [10/2013 - ] - Step 23
  7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT  . Refer to INSTALLATION [10/2013 - ] - Step 24
  8. INSTALL FRONT NO. 1 CONSOLE BOX INSERT  . Refer to INSTALLATION [10/2013 - ] - Step 25
  9. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET  . Refer to INSTALLATION [10/2013 - ] - Step 26
  10. INSTALL NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY  . Refer to INSTALLATION [10/2013 - ] - Step 1
  11. INSTALL REAR CONSOLE BOX ASSEMBLY 

    Refer to INSTALLATION [10/2013 - ]

  12. INSTALL GLOVE COMPARTMENT DOOR  . Refer to INSTALLATION [10/2013 - ] - Step 15
  13. INSTALL NO. 2 INSTRUMENT PANEL REGISTER  . Refer to INSTALLATION [10/2013 - ] - Step 16
  14. INSTALL NO. 1 SIDE DEFROSTER NOZZLE  . Refer to INSTALLATION [10/2013 - ] - Step 17
  15. INSTALL NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System)  . Refer to INSTALLATION [10/2013 - ] - Step 6
  16. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)  . Refer to INSTALLATION [10/2013 - ] - Step 5
  17. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY  . Refer to INSTALLATION [10/2013 - ] - Step 27
  18. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH  . Refer to INSTALLATION [10/2013 - ] - Step 28
  19. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY  . Refer to INSTALLATION [10/2013 - ] - Step 30
  20. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY  . Refer to INSTALLATION [10/2013 - ] - Step 31
  21. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL 

    Refer to INSTALLATION [10/2013 - ] - Step 2

  22. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION 

    Refer to CALIBRATION [10/2013 - ]

scientia non olet · About LEMON Manuals