LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2014 >> RAV4 LE, AWD >> Repair and Diagnosis (Single Page) >> Body & Frame >> Door Locks >> Smart Key System (Start Function) (Diagnostics - Introduction) (Except Hybrid) >> SMART KEY SYSTEM (For Start Function) >> DTC Check / Clear [12/2012 - ] >> DTC Check / Clear [12/2012 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Check / Clear [12/2012 - ]

NOTE:

If the Techstream is connected to the vehicle with the engine switch off, the information stored in smart key system related ECUs cannot be read. However, smart key system DTCs and Data List information can be confirmed even if the engine switch is off using the method below:

  • Connect the Techstream to the vehicle, and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and vehicle begins (the Techstream screen changes when communication begins).
  • Connect the Techstream to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body Electrical / Smart Key / Trouble Codes.
  1. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [POWER SOURCE CONTROL]) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > Power Source Control > Trouble Codes 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  2. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [STARTING CONTROL]) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Starting Control / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > Starting Control > Trouble Codes 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  3. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [SMART KEY]) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Smart Key / Trouble Codes.
    5. Check for DTCs.

      Body Electrical > Smart Key > Trouble Codes 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  4. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [POWER SOURCE CONTROL]) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.
    5. Clear the DTCs by following the directions on the Techstream display.

      Body Electrical > Power Source Control > Clear DTCs 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  5. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [STARTING CONTROL]) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Starting Control / Trouble Codes.
    5. Clear the DTCs by following the directions on the Techstream display.

      Body Electrical > Starting Control > Clear DTCs 

      HINT: 

      Refer to the Techstream operator's manual for further details.

  6. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [SMART KEY]) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Smart Key / Trouble Codes.
    5. Clear the DTCs by following the directions on the Techstream display.

      Body Electrical > Smart Key > Clear DTCs 

      HINT: 

      Refer to the Techstream operator's manual for further details.

scientia non olet · About LEMON Manuals