DTC P2767: Input / Turbine Speed Sensor "B" Circuit No Signal [08/2016 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
5. According to the display on the Techstream, read the Data List.

   Powertrain > Engine and ECT > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Engine Speed	Engine speed	min.: 0 rpm max.: 16383 rpm	700 to 800 rpm: Idling	When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
   SPD (NIN)	Primary pulley speed (NIN)	min.: 0 rpm max.: 12750 rpm	0 rpm: Vehicle stopped Primary pulley speed (NIN) equal to engine speed (NE): Lock-up ON (After warming up engine)	Data is displayed in increments of 50 rpm.
   Lock Up	Lock-up	OFF or ON	ON: Lock-up operating OFF: Lock-up not operating	-

   Powertrain > Engine and ECT > Data List 

   Tester Display
   Engine Speed
   SPD (NIN)
   Lock Up

   Result

   Result	Proceed to
   Data List values are not normal	A
   Data List values are normal	B

Result:  2

B 

See step  5

Result:  1

A 

See step  2

1. Disconnect the B30 transmission revolution sensor (NIN) connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Transmission Revolution Sensor (NIN))

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   2 - 1	20°C (68°F)	560 to 680 Ω

3. Connect the B30 transmission revolution sensor (NIN) connector.

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPLACE TRANSMISSION REVOLUTION SENSOR (NIN). Refer to  COMPONENTS [08/2013 - ] 

Result:  1

OK 

See step  3

1. Disconnect the B33 ECM connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   B33-127 (NIN+) - B33-128 (NIN-)	20°C (68°F)	560 to 680 Ω
   B33-127 (NIN+) - Body ground and other terminals	Always	10 kΩ or higher
   B33-128 (NIN-) - Body ground and other terminals	Always	10 kΩ or higher

3. Connect the B33 ECM connector.

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM) 

Result:  1

OK 

See step  4

1. Replace the ECM.
   • for 2ZR-FAE: Refer to COMPONENTS [08/2016 - ]
   • for 2ZR-FE: Refer to COMPONENTS [08/2016 - ]

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

PERFORM INITIALIZATION. Refer to  INITIALIZATION [08/2016 - ] 

1. Replace the ECM.
   • for 2ZR-FAE: Refer to COMPONENTS [08/2016 - ]
   • for 2ZR-FE: Refer to COMPONENTS [08/2016 - ]

   Result

   Proceed to
   NEXT

Result:  1

NEXT 

PERFORM INITIALIZATION. Refer to  INITIALIZATION [08/2016 - ]