Operation Check [12/2014 - ]

HINT: 

Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).

Fig 1: Window Lock Switch

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Check that the front passenger and rear windows* cannot be operated when the window lock switch of the power window regulator master switch assembly is pushed in.

   OK

   Front passenger and rear windows* are disabled.

   • *: w/ Rear Power Window
2. Check that the front passenger and rear windows* can be operated when the window lock switch of the power window regulator master switch assembly is pushed in again.

   OK

   Front passenger and rear windows* operate normally.

   • *: w/ Rear Power Window

1. Check that the driver door power window operates as follows:
   OK
   
   

   Condition	Master Switch	Switch Operation	Power Window
   Ignition switch ON (IG)	Driver door	Pulled halfway up	UP (Closes)
   		Pushed halfway down	DOWN (Opens)

2. Check that the front passenger door window and rear power windows operate as follows:
   OK
   
   

   Condition	Regulator Switch	Switch Operation	Power Window
   Ignition switch ON (IG) Window lock switch off	Front passenger door	Pulled up	UP (Closes)
   		Pushed down	DOWN (Opens)
   	Rear LH door*	Pulled up	UP (Closes)
   		Pushed down	DOWN (Opens)
   	Rear RH door*	Pulled up	UP (Closes)
   		Pushed down	DOWN (Opens)

   • *: w/ Rear Power Window

1. Check that the driver door power window operates as follows:
   OK
   
   

   Condition	Master Switch	Switch Operation	Power Window
   Ignition switch ON (IG)	Driver door	Pulled up (One touch operation)	AUTO UP (Closes)
   		Pushed down (One touch operation)	AUTO DOWN (Opens)

1. Check that the front passenger door window and rear power windows operate as follows:
   OK
   
   

   Condition	Master Switch	Switch Operation	Power Window
   Ignition switch ON (IG) Window lock switch off	Front passenger door	Pulled up	UP (Closes)
   		Pushed down	DOWN (Opens)
   	Rear LH door*	Pulled up	UP (Closes)
   		Pushed down	DOWN (Opens)
   	Rear RH door*	Pulled up	UP (Closes)
   		Pushed down	DOWN (Opens)

   • *: w/ Rear Power Window

1. Check that all the power windows can be operated with the power widow regulator master switch assembly and power window regulator switch assemblies (for front passenger door, rear LH and RH doors*) after the ignition switch is turned off.

   HINT: 

   If the window lock switch is on, the power windows cannot be operated besides the driver door power window. Therefore, turn the window lock switch off before checking the window operation.

   • *: w/ Rear Power Window
2. Check that the key-off operation function does not operate after the driver door or front passenger door is opened immediately.

   HINT: 

   If the driver door or front passenger door is opened during automatic window operation while the key-off operation function is on, the window will stop operating.

3. Check that all the power windows cannot be operated after more than approximately 43 seconds have elapsed since the ignition switch was turned off.

1. Check the basic function.
   WARNING: Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.

   HINT: 

   The jam protection function operates during both the auto up and manual up operations while the hybrid control system is started or the ignition switch is ON (IG), and also 43 seconds have elapsed after the ignition switch was turned off.

   1. Fully open the driver door window.
   2. Set a check jig wrapped with a piece of cloth near the window fully closed position.
      Fig 2: Checking With Check Jig

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION
      
      

      *a	Check Jig
      *b	Cloth

   3. Operate the auto up or manual up function to check that the power window stops and goes down after the check jig is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.) or until approximately 5 seconds elapse.

      HINT: 

      If the check jig is caught when the opening is approximately 75 mm (2.95 in.) or more, the power window goes down for approximately 125 mm (4.93 in.) or until approximately 2.5 seconds elapse.

   4. While the power window is moving down, check that the door glass cannot be raised when the power window switch is used.

1. Check the LED illumination (power window regulator master switch assembly).
   1. Check that the LED located on the power window regulator master switch assembly illuminates when the ignition switch is turned to ON (IG).