DTC C2111/11: Transmitter ID1 Operation Stop; DTC C2112/12: Transmitter ID2 Operation Stop; DTC C2113/13: Transmitter ID3 Operation Stop; DTC C2114/14: Transmitter ID4 Operation Stop [08/2014 - ]: Procedure

1. Set the tire pressure to the specified value. Refer to INSPECTION [08/2014 - ] .
2. Turn the power switch off.
3. Connect the Techstream to the DLC3.
4. Turn the power switch on (IG).
5. Turn the Techstream on.
6. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
7. Read the Data List according to the display on the Techstream.
   TIRE PRESSURE MONITOR
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   ID 1 Tire Inflation Pressure	ID1 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2 , 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2 , 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2 , 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1
   ID 2 Tire Inflation Pressure	ID2 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2 , 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2 , 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2 , 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1
   ID 3 Tire Inflation Pressure	ID3 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2 , 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2 , 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2 , 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1
   ID 4 Tire Inflation Pressure	ID4 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2 , 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2 , 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2 , 55 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*1

   HINT: 

   • *1: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24. Refer to DTC C2121/21: No Signal from Transmitter ID1; DTC C2122/22: No Signal from Transmitter ID2; DTC C2123/23: No Signal from Transmitter ID3; DTC C2124/24: No Signal from Transmitter ID4; DTC C2181/81: Transmitter ID1 not Received (Test Mode DTC); DTC C2182/82: Transmitter ID2 not Received (Test Mode DTC); DTC C2183/83: Transmitter ID3 not Received (Test Mode DTC); DTC C2184/84: Transmitter ID4 not Received (Test Mode DTC) [08/2014 - ] .
8. Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm² , 5.8 psi) within 30 seconds.
   1. Check that each "ID Tire Inflation Pressure" value displayed on the Techstream has changed.

      OK

      Each "ID Tire Inflation Pressure" value displayed on the Techstream changed to the actual tire inflation pressure value.

      NOTE:

      • It may take a few minutes until the values are displayed.
      • When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.
   2. After confirming that all of the tire "ID Tire Inflation Pressure" values displayed on the Techstream have changed, set the tire pressure to the appropriate specified values.

      HINT: 

      If an "ID Tire Inflation Pressure" value displayed on the Techstream has not changed after rechecking, inspect for another problem. Refer to DTC C2121/21: No Signal from Transmitter ID1; DTC C2122/22: No Signal from Transmitter ID2; DTC C2123/23: No Signal from Transmitter ID3; DTC C2124/24: No Signal from Transmitter ID4; DTC C2181/81: Transmitter ID1 not Received (Test Mode DTC); DTC C2182/82: Transmitter ID2 not Received (Test Mode DTC); DTC C2183/83: Transmitter ID3 not Received (Test Mode DTC); DTC C2184/84: Transmitter ID4 not Received (Test Mode DTC) [08/2014 - ] .

NG → See step   2 

OK → END