LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2016 >> Avalon XLE Plus >> Repair and Diagnosis (Single Page) >> Steering >> Steering Control Systems >> Lane Departure Alert System (W/ Steering Control) - Diagnostics - Introduction - (Except Hybrid) >> LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) >> Data List / Active Test [10/2015 - ] >> Data List / Active Test [10/2015 - ]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test [10/2015 - ]

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Chassis / LKA/LDA / Data List.
    5. Read the Data List according to the display on the Techstream.
      LKA/LDA

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      LDA Control lane departure alert system control status/
      Prohibit or Permit
      Prohibit: Control prohibited
      Permit: Control permitted
      -
      Turn Signal Switch (Right) Turn signal switch (right) status/
      OFF or ON
      ON: Turn signal light switch on (right)
      OFF: Turn signal light switch off
      -
      Turn Signal Switch (Left) Turn signal switch (left) status/
      OFF or ON
      ON: Turn signal light switch on (left)
      OFF: Turn signal light switch off
      -
      Left Lane Indicator Left lane marker detection status/
      Nothing, Heavy, Thin or H blink
      Nothing: Lane departure alert system deactivated
      Heavy: Left lane marker detected
      Thin: Left lane marker not detected
      H blink: Departing from lane
      -
      Right Lane Indicator Right lane marker detection status/
      Nothing, Heavy, Thin or H blink
      Nothing: Lane departure alert system deactivated
      Heavy: Right lane marker detected
      Thin: Right lane marker not detected
      H blink: Departing from lane
      -
      Skid Control Buzzer Demand LDA Buzzer Demand Status/
      OFF or ON
      OFF: LDA buzzer not operating
      ON: LDA buzzer operating
      -
      The Number of DTCs Number of stored DTCs/
      min.: 0, max.: 255
      Number of stored DTCs -
    6. Enter the following menus: Chassis / LKA/LDA (Sub) / Data List.
    7. Read the Data List according to the display on the Techstream.
      LKA/LDA (SUB)

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Engine / HV Communication Failure Error in CAN communication between driving support ECU assembly and ECM/
      OFF or ON
      OFF: No communication errors exist
      ON: Communication error exists
      -
      DRS Communication Failure - - This item is displayed on the Techstream but is not used.
      Meter Communication Failure Error in CAN communication between driving support ECU assembly and combination meter assembly/
      OFF or ON
      OFF: No communication errors exist
      ON: Communication error exists
      -
      Yaw Rate Sensor Communication Failure Error in CAN communication between driving support ECU assembly and yaw Rate Sensor/
      OFF or ON
      OFF: No communication errors exist
      ON: Communication error exists
      -
      Steering Angle Sensor Communication Failure Error in CAN communication between driving support ECU assembly and steering angle sensor/
      OFF or ON
      OFF: No communication errors exist
      ON: Communication error exists
      -
      EPS Communication Failure Error in CAN communication between driving support ECU assembly and power steering ECU assembly/
      OFF or ON
      OFF: No communication errors exist
      ON: Communication error exists
      -
      VSC Communication Failure Error in CAN communication between driving support ECU assembly and skid control ECU/
      OFF or ON
      OFF: No communication errors exist
      ON: Communication error exists
      -
      VGRS Communication Failure - - This item is displayed on the Techstream but is not used.
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Chassis / LKA/LDA / Active Test.
    5. Perform Active Test according to the display on the Techstream.

      HINT: 

      The engine switch must be turned on (IG) to proceed with the Active Test using the Techstream.

      LKA/LDA

      Tester Display Measurement Item Control Range Diagnostic Note
      LDA Buzzer Sounds the LDA buzzer ON/OFF Confirm that the vehicle is stopped with the engine switch on (IG).
    6. Enter the following menus: Body Electrical / Combination Meter / Active Test.
    7. Perform Active Test according to the display on the Techstream.

      HINT: 

      The engine switch must be turned on (IG) to proceed with the Active Test using the Techstream.

      COMBINATION METER

      Tester Display Measurement Item Control Range Diagnostic Note
      Meter Display 1 Multi-information display OFF or ALL -