LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2016 >> Corolla LE >> Repair and Diagnosis (Single Page) >> Body & Frame >> Windows >> Power Window Control System - Diagnostic Codes & Symptom Tests (Model Code: ZRE172) >> Power Window Control System >> Symptom Tests >> Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch [08/2013 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch [08/2013 - ]: Procedure

  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BATTERY) 
    1. Disconnect the G4 power window regulator switch assembly connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      G4-3 (B) - Body ground Ignition switch ON 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    OK 

    See step  2

  2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY 
    1. Remove the power window regulator switch assembly.

      Refer to REMOVAL [08/2013 - ]

    2. Inspect the power window regulator switch assembly.

      Refer to INSPECTION [08/2013 - ]

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY:  REMOVAL [08/2013 - ] 

    Result:  1

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) 
    1. Disconnect the G10 power window regulator motor assembly (for front passenger door) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G4-4 (U) - G10-2 (U) Always Below 1 Ω
      G4-1 (D) - G10-1 (D) Always Below 1 Ω
      G4-4 (U) - Body ground Always 10 kΩ or higher
      G4-1 (D) - Body ground Always 10 kΩ or higher
      G10-2 (U) - Body ground Always 10 kΩ or higher
      G10-1 (D) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    OK 

    See step  4

  4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY 
    1. Remove the power window regulator master switch assembly.

      Refer to REMOVAL [08/2013 - ]

    2. Inspect the power window regulator master switch assembly.

      Refer to INSPECTION [08/2013 - ]

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY:  REMOVAL [08/2013 - ] 

    Result:  1

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H5-16 (U) - G4-5 (SU) Always Below 1 Ω
      H5-15 (D) - G4-2 (SD) Always Below 1 Ω
      H5-16 (U) - Body ground Always 10 kΩ or higher
      H5-15 (D) - Body ground Always 10 kΩ or higher
      G4-5 (SU) - Body ground Always 10 kΩ or higher
      G4-2 (SD) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR). Refer to  REMOVAL [08/2013 - ] 

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR