Front Passenger Side Seat Belt Warning Light Malfunction [08/2013 - 04/2014]: Procedure
- CHECK DTC OUTPUT (OCCUPANT CLASSIFICATION SYSTEM)
- Clear the DTCs.
Refer to DTC CHECK / CLEAR [08/2013 - ]
Body Electrical > Occupant Detection > Clear DTCs
- Check for DTCs.
Refer to DTC CHECK / CLEAR [08/2013 - ]
Body Electrical > Occupant Detection > Trouble Codes
Result
Result Proceed to DTCs are not output A DTCs are output B
Result: 2
B
GO TO OCCUPANT CLASSIFICATION SYSTEM: DIAGNOSTIC TROUBLE CODE CHART [08/2013 - 08/2016]
Result: 1
A
See step 2
- Clear the DTCs.
- CHECK DTC OUTPUT (AIRBAG SYSTEM)
- Clear the DTCs.
Refer to DTC CHECK / CLEAR [08/2013 - ]
Body Electrical > SRS Airbag > Clear DTCs
- Check for DTCs.
Refer to DTC CHECK / CLEAR [08/2013 - ]
Body Electrical > SRS Airbag > Trouble Codes
Result
Result Proceed to DTCs are not output A DTCs are output B
Result: 2
B
GO TO AIRBAG SYSTEM: DIAGNOSTIC TROUBLE CODE CHART [08/2013 - 04/2014]
Result: 1
A
See step 3
- Clear the DTCs.
- READ VALUE USING TECHSTREAM (OCCUPANT DETECTION)
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Occupant Detection / Data List.
- Read the Data List according to the display on the Techstream.
Body Electrical > Occupant Detection > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Passenger Buckle SW Front passenger buckle switch Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data is not determined- Body Electrical > Occupant Detection > Data List
Tester Display Passenger Buckle SW Result
Result Proceed to Unset or Set is displayed on the Techstream according to the front passenger seat belt condition A Unset or Set is not displayed correctly on the Techstream according to the front passenger seat belt condition B NG is displayed on the Techstream C
Result: 2
B
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH. Refer to REMOVAL [08/2013 - 04/2014]
Result: 3
C
REPLACE OCCUPANT DETECTION ECU. Refer to REMOVAL [08/2013 - ]
Result: 1
A
See step 4
- READ VALUE USING TECHSTREAM (SRS AIRBAG)
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Body Electrical / SRS Airbag / Data List.
- Read the Data List according to the display on the Techstream.
Body Electrical > SRS Airbag > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Right side Buckle SW RH buckle switch Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data is not determined- Body Electrical > SRS Airbag > Data List
Tester Display Right side Buckle SW Result
Result Proceed to Unset or Set is displayed on the Techstream according to the front passenger seat belt condition A - Unset or Set is not displayed correctly on the Techstream according to the front passenger seat belt condition
- NG is displayed on the Techstream
B
Result: 1
A
USE SIMULATION METHOD TO CHECK. Refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2013 - 04/2014]
Result: 2
B
REPLACE AIRBAG SENSOR ASSEMBLY. Refer to REMOVAL [08/2013 - ]