DTC B1788: Rear Occupant Classification Sensor RH Collision Detection [08/2015 - 08/2019]: Procedure

1. Turn the ignition switch to ON, and wait for at least 60 seconds.
2. Clear the DTCs stored in the center airbag sensor (Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] ).
3. Turn the ignition switch off.
4. Turn the ignition switch to ON, and wait for at least 60 seconds.
5. Using the Techstream, check for DTCs of the occupant classification ECU (Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] ).

   OK

   DTC B1788 is not output.

   HINT: 

   DTCs other than DTC B1788 may be output at this time, but they are not related to this check.

Result: 

OK 

USE SIMULATION METHOD TO CHECK 

(Refer to DIAGNOSIS SYSTEM [08/2015 - ] )

Result: 

NG 

See step  2

1. Using the Techstream, perform the zero point calibration (Refer to INITIALIZATION [08/2015 - ] ).

   OK

   "Zero Point Calibration is complete." is displayed.

Result: 

NG 

See step  5

Result: 

OK 

See step  3

1. Using the Techstream, perform the sensitivity check (Refer to INITIALIZATION [08/2015 - ] ).

   Standard range

   27 to 33 kg (59.5 to 72.8 lb)

Result: 

NG 

See step  5

Result: 

OK 

See step  4

1. Clear the DTCs stored in the center airbag sensor (Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] ).
2. Turn the ignition switch off.
3. Turn the ignition switch to ON, and wait for at least 60 seconds.
4. Using the Techstream, check for DTCs of the occupant classification ECU (Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] ).

   OK

   DTC B1788 is not output.

   HINT: 

   DTCs other than DTC B1788 may be output at this time, but they are not related to this check.

Result: 

OK 

END 

Result: 

NG 

See step  5

1. Turn the ignition switch off.
2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
3. for Manual Seat:
   1. Replace the separate type front seat cushion spring RH (Refer to DISASSEMBLY [08/2015 - ] ).
4. for Power Seat:
   1. Replace the separate type front seat cushion spring RH (Refer to DISASSEMBLY [08/2015 - ] ).

   HINT: 

   Perform the inspection using parts from a normal vehicle when possible.

Result: 

NEXT 

See step  6

1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
2. Turn the ignition switch to ON, and wait for at least 60 seconds.
3. Using the Techstream, perform the zero point calibration (Refer to INITIALIZATION [08/2015 - ] ).

   OK

   "Zero Point Calibration is complete." is displayed.

Result: 

NG 

See step  9

Result: 

OK 

See step  7

1. Using the Techstream, perform the sensitivity check (Refer to INITIALIZATION [08/2015 - ] ).

   Standard range

   27 to 33 kg (59.5 to 72.8 lb)

Result: 

NG 

See step  9

Result: 

OK 

See step  8

1. Clear the DTCs stored in memory (Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] ).

   HINT: 

   • First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
   • Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.
2. Turn the ignition switch off.
3. Turn the ignition switch to ON, and wait for at least 60 seconds.
4. Using the Techstream, check for DTCs of the occupant classification ECU (Refer to DTC CHECK / CLEAR [08/2015 - 08/2019] ).

   OK

   DTC B1788 is not output.

   HINT: 

   DTCs other than DTC B1788 may be output at this time, but they are not related to this check.

Result: 

OK 

END 

Result: 

NG 

See step  9

1. Turn the ignition switch off.
2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
3. Replace the occupant classification ECU (Refer to REMOVAL [08/2015 - ] ).

   HINT: 

   Perform the inspection using parts from a normal vehicle when possible.

Result: 

NEXT 

See step  10

1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
2. Turn the ignition switch to ON, and wait for at least 60 seconds.
3. Using the Techstream, perform the zero point calibration (Refer to INITIALIZATION [08/2015 - ] ).

   OK

   "Zero Point Calibration is complete." is displayed.

Result: 

NEXT 

See step  11

1. Using the Techstream, perform the sensitivity check (Refer to INITIALIZATION [08/2015 - ] ).

   Standard range

   27 to 33 kg (59.5 to 72.8 lb)

Result: 

NEXT 

END