LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2017 >> 4Runner TRD Pro >> Repair and Diagnosis (Single Page) >> Steering >> Steering Column >> Steering Column - Service Information >> Steering Column Assembly >> Installation [08/2015 - 08/2022] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Installation [08/2015 - 08/2022]: Procedure

  1. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY 
    1. Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.
    2. Install the bolt.

      Torque: 36 N.m (367 kgf/cm, 27 ft.lbf) 

  2. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY 
    1. Install the 4 bolts.

      Torque: 5.0 N.m (51 kgf/cm, 44 in.lbf) 

      NOTE:

      Do not fold back the boot part of the steering hole cover or extend it excessively. If it is extended excessively, return it to its original position.

  3. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY 
    1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

      HINT: 

      Install the steering intermediate shaft from the inside of the vehicle.

    2. Install the bolt.

      Torque: 36 N.m (367 kgf/cm, 27 ft.lbf) 

  4. INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL LH 

    Refer to PROCEDURE - Step 19

  5. INSTALL STEERING COLUMN ASSEMBLY 
    1. Align the matchmarks on the steering intermediate shaft and steering column.
    2. Install the steering column with the 4 nuts.

      Torque: 15 N.m (153 kgf/cm, 11 ft.lbf) 

    3. Install the bolt.

      Torque: 36 N.m (367 kgf/cm, 27 ft.lbf) 

    4. Attach the claws to connect the wire harness.
  6. INSTALL NO. 1 INSTRUMENT LOWER PANEL AIRBAG ASSEMBLY 
    1. Install the instrument lower panel airbag assembly (Refer to INSTALLATION [08/2015 - ] ).
  7. INSTALL TRANSPONDER KEY AMPLIFIER (w/ Transponder Key) 
    1. Install the transponder key amplifier (Refer to INSTALLATION [08/2015 - 08/2019] , or refer to INSTALLATION [08/2019 - 08/2022] ).
  8. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 
    1. Using pliers, grip the claws of the clamp and install the combination switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
    2. Connect the connectors to the combination switch with spiral cable.
  9. INSTALL STEERING COLUMN UPPER COVER 
    1. Attach the claw to install the steering column upper cover.
    2. Attach the 4 clips to install the steering column upper cover to the instrument cluster finish panel.
  10. INSTALL STEERING COLUMN LOWER COVER 
    1. Attach the 2 claws to install the steering column lower cover.
    2. Install the 2 screws.
  11. INSTALL STEERING WHEEL ASSEMBLY 
    1. Install the steering wheel assembly (Refer to INSTALLATION [08/2015 - 08/2022] ).
  12. CHECK FRONT WHEELS FACING STRAIGHT AHEAD 
  13. INSTALL FRONT WHEEL LH 

    for aluminum wheel 

    Torque: 103 N.m (1050 kgf/cm, 76 ft.lbf) 

    for steel wheel 

    Torque: 112 N.m (1142 kgf/cm, 83 ft.lbf) 

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Refer to INITIALIZATION [08/2015 - 08/2019] , or refer to INITIALIZATION [08/2019 - 08/2022] ).

  15. CHECK SRS WARNING LIGHT 
    1. Check the SRS warning light (Refer to DIAGNOSIS SYSTEM [08/2015 - 08/2019] , or refer to DIAGNOSIS SYSTEM [08/2019 - ] ).
scientia non olet · About LEMON Manuals