Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch [08/2013 - ]: Procedure
- CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BATTERY)
- Disconnect the G4 power window regulator switch assembly connector.
- Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition G4-3 (B) - Body ground Ignition switch ON 11 to 14 V Result
Proceed to OK NG
Result: 2
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result: 1
OK
See step 2
- INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
- Remove the power window regulator switch assembly.
Refer to REMOVAL [08/2013 - ]
- Inspect the power window regulator switch assembly.
Refer to INSPECTION [08/2013 - ]
Result
Proceed to OK NG
Result: 2
NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY: REMOVAL [08/2013 - ]
Result: 1
OK
See step 3
- Remove the power window regulator switch assembly.
- CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)
- Disconnect the G10 power window regulator motor assembly (for front passenger door) connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition G4-4 (U) - G10-2 (U) Always Below 1 Ω G4-1 (D) - G10-1 (D) Always Below 1 Ω G4-4 (U) - Body ground Always 10 kΩ or higher G4-1 (D) - Body ground Always 10 kΩ or higher G10-2 (U) - Body ground Always 10 kΩ or higher G10-1 (D) - Body ground Always 10 kΩ or higher Result
Proceed to OK NG
Result: 2
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result: 1
OK
See step 4
- INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
- Remove the power window regulator master switch assembly.
Refer to REMOVAL [08/2013 - ]
- Inspect the power window regulator master switch assembly.
Refer to INSPECTION [08/2013 - ]
Result
Proceed to OK NG
Result: 2
NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY: REMOVAL [08/2013 - ]
Result: 1
OK
See step 5
- Remove the power window regulator master switch assembly.
- CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY)
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition H5-16 (U) - G4-5 (SU) Always Below 1 Ω H5-15 (D) - G4-2 (SD) Always Below 1 Ω H5-16 (U) - Body ground Always 10 kΩ or higher H5-15 (D) - Body ground Always 10 kΩ or higher G4-5 (SU) - Body ground Always 10 kΩ or higher G4-2 (SD) - Body ground Always 10 kΩ or higher Result
Proceed to OK NG
Result: 1
OK
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR). Refer to REMOVAL [08/2013 - ]
Result: 2
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
- Measure the resistance according to the value(s) in the table below.