LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2017 >> Corolla LE >> Repair and Diagnosis >> Steering >> Steering Column >> Steering Column (Service Information) (Model Code: ZRE172) >> Steering Column Assembly >> Removal [08/2013 - 04/2014] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Removal [08/2013 - 04/2014]: Procedure

  1. PRECAUTION 

    Refer to PRECAUTION [08/2013 - 04/2014]

  2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD 
  3. REMOVE HORN BUTTON ASSEMBLY 

    Refer to REMOVAL [08/2013 - ]

  4. REMOVE STEERING WHEEL ASSEMBLY 

    See step  3

  5. REMOVE LOWER STEERING COLUMN COVER 
    1. Remove the 2 screws.
      GTY431152Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 5 claws and remove the lower steering column cover.
      GTY451995Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE UPPER STEERING COLUMN COVER 
    1. Disengage the 2 claws and remove the upper steering column cover.
      GTY431151Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 
    NOTE:
    • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.
    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly with the battery connected and the ignition switch ON.
    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
    1. Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.
    2. Using pliers, expand the clamp.
      GTY455583Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Clamp
      *b Claw
    3. While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
  8. REMOVE COLUMN HOLE COVER SILENCER SHEET 
    1. Turn back the floor carpet.
    2. Remove the 2 clips and column hole cover silencer sheet.
      GTY431154Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 
    1. Put matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.
      GTY444945Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
    2. Remove the bolt.
    3. Separate the No. 2 steering intermediate shaft assembly from the steering intermediate shaft assembly.
  10. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY 

    Refer to REMOVAL [08/2013 - 04/2014]

  11. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY 

    Refer to REMOVAL [08/2013 - 04/2014]

  12. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 
    1. Remove the bolt and slide the No. 2 steering intermediate shaft assembly.
      GTY448504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
      NOTE:

      Do not remove the No. 2 steering intermediate shaft assembly from the steering column assembly.

    2. Put matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly.
    3. Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.
  13. REMOVE STEERING COLUMN ASSEMBLY 
    1. Disconnect the 2 connectors.
      GTY451997Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clamp.
    3. Disconnect each connector and disengage each wire harness clamp from the steering column assembly.
    4. Remove the bolt, 2 nuts and steering column assembly.
      GTY431157Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals