LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2017 >> Corolla SE, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 5 (Continuously Variable Transaxle (Service Information) (Model Code: ZRE172)) >> Shift Lever >> Disassembly [08/2013 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Disassembly [08/2013 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. HOW TO PREVENT STATIC ELECTRICITY 
    NOTE:
    • Be sure to touch a grounded metal surface with your bare hands to discharge any static electricity before removing or installing the transmission floor shift assembly.
    • Do not touch the electronic components of a circuit board.
    • Keep clothes away from electronic components.
    • Place electronic components removed from the transmission floor shift assembly on SST (anti-static mat).
    1. Wear SST (wrist band).
      GTY477356Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09890-47010 
    2. Connect the ground clip of SST (anti-static mat) securely to a ground point provided in the workshop or on a workbench (anchor bolt).
      • SST: 09890-47010 

      HINT: 

      If the ground clip cable is too short, use an extension cable.

    3. Connect the ground clip of the antistatic wrist strap securely to the specified point of the antistatic mat.
  2. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY 
    1. Disengage the 4 claws to remove the floor shift position indicator housing sub-assembly from the lower position indicator housing.
      GTY474600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not damage the lower position indicator housing.

  3. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY 
    1. Disengage the 3 claws to remove the shifting hole cover sub-assembly from the floor shift position indicator housing sub-assembly.
      GTY474599Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not damage the floor shift position indicator housing sub-assembly.

  4. REMOVE POSITION INDICATOR LIGHT GUIDE 
    1. Disengage the 5 claws to remove the position indicator light guide from the floor shift position indicator housing sub-assembly.
      GTY474598Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not damage the position indicator light guide and floor shift position indicator housing sub-assembly.

  5. REMOVE SHIFT POSITION INDICATOR 
    1. Disconnect the indicator light wire sub-assembly connector.
      GTY481472Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 guides to remove the shift position indicator from the lower position indicator housing.
      GTY474597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not damage the shift position indicator.

  6. REMOVE INDICATOR LIGHT WIRE SUB-ASSEMBLY (w/o Sport Sequential Shiftmatic) 
    1. Disengage the guide.
      GTY479228Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Guide
      *b Clamp
    2. Disengage the clamp to remove the indicator light wire sub-assembly from the shift lock control unit assembly.
    3. Disengage the claw to remove the clamp from the transmission control switch connector.
      GTY474607Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using a screwdriver, release the secondary lock.
      GTY477146Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Secondary Lock
      *b Protective Tape

      HINT: 

      Tape the screwdriver tip before use.

    5. Using SST, release the locking lugs of terminals 4, 5, 6, 7, 8, 9, 10, 13, and 14, and pull the wires and terminals out of the transmission control switch connector.
      GTY478229Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Rear view of wire harness connector
      (Transmission Control Switch Connector)
      Indicator Light Wire Sub-assembly Terminal
      • SST: 09991-00510 
      NOTE:

      Before pulling out the terminals and wires, make a note of the wire color and where each terminal is connected.

  7. REMOVE INDICATOR LIGHT WIRE SUB-ASSEMBLY (w/ Sport Sequential Shiftmatic) 
    1. Disengage the guide.
      GTY474951Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Guide
      *b Clamp
    2. Disengage the clamp to remove the indicator light wire sub-assembly from the shift lock control unit assembly.
    3. Disengage the claw to remove the clamp from the indicator light wire sub-assembly.
      GTY474605Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE LOWER POSITION INDICATOR HOUSING 
    1. Disengage the 5 claws to remove the lower position indicator housing from the shift lock control unit assembly.
      GTY474606Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not damage the shift lock control unit assembly.

scientia non olet · About LEMON Manuals