Key-off Operation Function Operates even if Operating Conditions are not Satisfied [12/2013 - ]: Procedure

1. Check that the manual up and down function using the power window regulator master switch assembly, power window regulator switch assembly and rear power window regulator switch assembly (for LH or RH door) can operate the power windows.

   Refer to OPERATION CHECK [12/2013 - ]

   OK

   Manual up and down function is normal.

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table). Refer to  PROBLEM SYMPTOMS TABLE [12/2013 - ] 

Result:  1

OK 

See step  2

1. Check that the remote up and down function using the power window regulator master switch assembly can operate all the power windows.

   Refer to OPERATION CHECK [12/2013 - ]

   OK

   Remote up and down function is normal.

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table). Refer to  PROBLEM SYMPTOMS TABLE [12/2013 - ] 

Result:  1

OK 

See step  3

1. Check the key-off operation function.

   Refer to OPERATION CHECK [12/2013 - ]

   Result

   Result	Proceed to
   Power window can still be operated even after opening driver door or front passenger door within approximately 43 seconds of ignition switch being turned off	A
   Power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for All Doors)	B
   Power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for Driver Door or Front Passenger Door)	C
   Power window can still be operated even after approximately 43 seconds have elapsed after ignition switch is turned off (for Rear LH Door or Rear RH Door)	D

Result:  2

B 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [12/2013 - ] 

Result:  3

C 

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR). Refer to  REMOVAL [12/2013 - ] 

Result:  4

D 

See step  5

Result:  1

A 

See step  4

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Data List.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   FR Door Courtesy SW	Front door courtesy light switch assembly (for RH) signal	OFF or ON	OFF: Front door RH closed ON: Front door RH open	-
   FL Door Courtesy SW	Front door courtesy light switch assembly (for LH) signal	OFF or ON	OFF: Front door LH closed ON: Front door LH open	-

   Body Electrical > Main Body > Data List 

   Tester Display
   FR Door Courtesy SW
   FL Door Courtesy SW

   OK

   On the Techstream screen, ON or OFF is displayed accordingly.

   Result

   Proceed to
   OK
   NG

Result:  1

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [12/2013 - ] 

Result:  2

NG 

GO TO LIGHTING SYSTEM (Proceed to Front Door Courtesy Switch Circuit). Refer to  Front Door Courtesy Switch Circuit [12/2013 - ] 

1. Replace the main body ECU (multiplex network body ECU).

   Refer to REMOVAL [12/2013 - ]

NEXT 

1. Check the key-off operation function.

   Refer to OPERATION CHECK [12/2013 - ]

   OK

   Key-off operation function is normal.

   Result

   Proceed to
   OK
   NG

Result:  1

OK 

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) 

Result:  2

NG 

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY. Refer to  REMOVAL [12/2013 - ]