LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2017 >> Sienna LE, AWD >> Repair and Diagnosis (Single Page) >> Body & Frame >> Windows >> Power Window Control System - Diagnostic Codes & Symptom Tests >> Power Window Control System >> Symptom Tests >> Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch [12/2015 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch [12/2015 - ]: Procedure

  1. READ VALUE USING TECHSTREAM (P-DOOR MOTOR) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / P-Door Motor / Data List.
    5. Read the Data List according to the display on the Techstream.
      P-DOOR MOTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door P/W Auto SW Front passenger side power window auto switch signal / ON or OFF ON: Front passenger side power window auto switch operated
      OFF: Front passenger side power window auto switch not operated
      -

      OK

      On the Techstream screen, ON or OFF is displayed accordingly.

    Result: 

    NG 

    See step  4

    Result: 

    OK 

    See step  2

  2. PERFORM INITIALIZATION (FOR FRONT PASSENGER SIDE) 
    1. Initialize the front power window regulator motor assembly RH (Refer to INITIALIZATION [12/2015 - ] ).

    Result: 

    NEXT 

    See step  3

  3. CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION) 
    1. Check that the front passenger side power window moves when the auto up/down function of the front power window regulator switch assembly RH is operated (Refer to OPERATION CHECK [12/2015 - ] ).

      OK

      Front passenger side auto up/down function is normal.

    Result: 

    OK 

    END (PROBLEM DUE TO INITIALIZATION FAILURE) 

    Result: 

    NG 

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH 

    (Refer to REMOVAL [12/2015 - ] )

  4. INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH 
    1. Remove the front power window regulator switch assembly RH (Refer to REMOVAL [12/2015 - ] ).
    2. Remove the front power window regulator switch assembly RH (Refer to INSPECTION [12/2015 - ] ).

    Result: 

    NG 

    REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH 

    (Refer to REMOVAL [12/2015 - ] )

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) 
    1. Disconnect the G15 front power window regulator switch assembly RH connector.
    2. Disconnect the G1 front power window regulator motor assembly RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G15-8 (AUTO) - G1-4 (AUTO) Always Below 1 Ω
      G15-8 (AUTO) - Body ground Always 10 kΩ or higher

    Result: 

    OK 

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH 

    (Refer to REMOVAL [12/2015 - ] )

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR