LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2017 >> Sienna LE, AWD >> Repair and Diagnosis (Single Page) >> Steering >> Steering Column >> Steering Column (Service Information) >> Steering Column Assembly >> Installation [12/2015 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Installation [12/2015 - ]: Procedure

  1. INSTALL STEERING COLUMN ASSEMBLY 
    1. Install the steering column assembly with the bolt and 2 nuts.

      Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf) 

      NOTE:

      Do not line up the bolt hole by prying on the collar or bushings. Only install the bolt in straight, without applying any force to the bushings.

    2. Engage the 3 wire harness clamps to the steering column assembly.
    3. Connect the 2 connectors.
  2. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY 
    1. Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.
    2. Install the bolt.

      Torque: 35 N*m (360 kgf*cm, 26 ft.*lbf) 

  3. INSTALL TRANSPONDER KEY AMPLIFIER (w/ Engine Immobiliser System) 
    1. Connect the connector to the transponder key amplifier.
    2. Align the transponder key amplifier with the steering column upper bracket. Tilt the amplifier slightly and slide it into position.
    3. Push the transponder key amplifier, and engage the 2 claws to install the transponder key amplifier to the steering column upper bracket.
      GTY204968Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 
    1. Using pliers, expand the clamp.
    2. While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.
    3. Return the clamp to its original position.
    4. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
  5. INSTALL UPPER STEERING COLUMN COVER 
    1. Engage the 4 clips and 2 guides to install the upper steering column cover to the instrument panel cluster finish panel.
    2. Engage the claw to install the upper steering column cover.
  6. INSTALL LOWER STEERING COLUMN COVER 
    1. Engage the 2 claws to install the lower steering column cover.
    2. Install the 2 screws.
  7. INSTALL STEERING WHEEL ASSEMBLY 

    See step  7

  8. INSTALL STEERING PAD 

    Refer to PROCEDURE - Step 1

  9. INSTALL LOWER NO. 2 STEERING WHEEL COVER 

    Refer to PROCEDURE - Step 3

  10. INSTALL LOWER NO. 3 STEERING WHEEL COVER 

    Refer to PROCEDURE - Step 2

  11. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 20 [12/2015 - 08/2016] , or refer to PROCEDURE - Step 21 [08/2016 - ]

  12. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY 

    (Refer to INSTALLATION [12/2015 - ] )

  13. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD 
  14. ADJUST SPIRAL CABLE 

    Refer to PROCEDURE - Step 4

  15. INSPECT STEERING WHEEL CENTER POINT 
  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 

    Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

    NOTE:
  17. INSPECT STEERING PAD 

    Refer to PROCEDURE - Step 1

  18. KEY REGISTRATION (w/ Smart Key System) 

    HINT: 

    When replacing the steering lock actuator assembly, perform the key registration (Refer to PROCEDURE - Step 4 [12/2015 - 08/2016] , or refer to PROCEDURE - Step 4 [08/2016 - ] ).

  19. INSPECT SRS WARNING LIGHT 

    (Refer to DIAGNOSIS SYSTEM [12/2015 - ] )

  20. PERFORM ASSIST MAP WRITING 

    HINT: 

    When replacing the steering column assembly, perform the assist map writing (Refer to REGISTRATION [12/2015 - ] ).

scientia non olet · About LEMON Manuals