Only Wireless Control Function is Inoperative [06/2016 - ]: Procedure

1. When the door control switch on the power window regulator master switch assembly is operated, check that the locked doors unlock (Refer to OPERATION CHECK [06/2016 - 03/2017] , or refer OPERATION CHECK [03/2017 - ] ).

   OK

   Locked doors unlock.

Result: 

NG 

GO TO POWER DOOR LOCK CONTROL SYSTEM 

(Refer to PROBLEM SYMPTOMS TABLE [06/2016 - ] )

Result: 

OK 

See step  2

1. Check that the key reminder warning buzzer operates normally (Refer to OPERATION CHECK [06/2016 - ] ).

   OK

   Key reminder warning buzzer operates normally.

Result: 

NG 

GO TO KEY REMINDER WARNING SYSTEM 

(Refer to PROBLEM SYMPTOMS TABLE [06/2016 - ] )

Result: 

OK 

See step  3

1. Switch to self-diagnostic mode by operating the ignition key cylinder.
   1. Insert the key into the ignition key cylinder and remove it.
   2. Within 5 seconds after the key is removed, insert it into the ignition key cylinder and then turn the ignition switch to ON then off once. (End in off)
   3. Within 30 seconds after turning the ignition switch off, perform the following 9 times: Turn the ignition switch to ON then off. (End in off)
      NOTE:

      If the system fails to enter self-diagnostic mode, the system will return to normal mode.

      HINT: 

      Turning the ignition switch to ON after the procedure above has been completed will end the self-diagnostic mode.

2. Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   OK

   Flash pattern is same as illustration on left.

Result: 

NEXT 

See step  4

1. Check the diagnostic outputs when the door control transmitter module set sub-assembly switch is held down. The diagnostic outputs can be checked by the interior light and wireless door lock buzzer patterns.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   RESULT
   
   

   Result	Proceed to
   Normal wave (light flash pattern and buzzer pattern) is output.	A
   Un matching recognition code is output.	B
   No diagnosis outputs	C

Result: 

A 

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) 

(Refer to REMOVAL [06/2016 - ] )

Result: 

C 

See step  6

Result: 

B 

See step  5

1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

   OK

   Recognition code can be registered.

Result: 

OK 

END 

Result: 

NG 

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY 

(Refer to REMOVAL [06/2016 - 03/2017] , or refer REMOVAL [03/2017 - ] )

1. Prepare the door control transmitter from another vehicle.
2. Press and hold down the door control transmitter switch.
3. Check that an un matching recognition code is output.

   OK

   Un matching recognition code is output.

Result: 

NG 

See step  10

Result: 

OK 

See step  7

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the battery from the door control transmitter module that does not operate. Attach a lead wire (0.6 mm (0.0236 in.)) or less in diameter including wire sheath) with tape or equivalent to the negative terminal (Refer to REPLACEMENT [06/2016 - 03/2017] , or refer REPLACEMENT [03/2017 - ] ).
   NOTE:

   Do not wrap the lead wire around the terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

   TEXT IN ILLUSTRATION
   
   

   *1

   Lead Wire

2. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
   NOTE:

   When replacing the transmitter battery, before starting work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

3. Measure the voltage according to the value(s) in the table below.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   When measuring the battery voltage, press one of the transmitter switches.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   Battery positive (+) - Battery negative (-)	Door control transmitter lock or unlock switch pushed	2.5 to 3.2 V

   TEXT IN ILLUSTRATION
   
   

   *a

   GND

Result: 

OK 

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY 

(Refer to REMOVAL [06/2016 - 03/2017] , or refer REMOVAL [03/2017 - ] )

Result: 

NG 

See step  8

1. Replace the transmitter battery (Refer to REPLACEMENT [06/2016 - 03/2017] , or refer REPLACEMENT [03/2017 - ] ).

Result: 

NEXT 

See step  9

1. Inspect the diagnostic outputs when the door control transmitter module set sub-assembly switch is held down. The diagnostic outputs can be checked by the flash patterns of the interior lights and the buzzer patterns of the wireless door lock buzzer.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   RESULT
   
   

   Result	Proceed to
   Normal wave (light flash pattern and buzzer pattern) is output.	A
   Unmatching recognition code is output	B
   No diagnosis outputs

Result: 

A 

END (TRANSMITTER BATTERY IS DEFECTIVE) 

Result: 

B 

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY 

(Refer to REMOVAL [06/2016 - 03/2017] , or refer REMOVAL [03/2017 - ] )

1. Bring the transmitter near the door control receiver, and perform a wireless operation check.

   OK

   Wireless functions operate normally.

   HINT: 

   • When the transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
   • If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

Result: 

NG 

AFFECTED BY WAVE INTERFERENCE 

Result: 

OK 

See step  11

1. Disconnect the H28 door control receiver connector.
2. Measure the resistance and voltage according to the value(s) in the table below.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   H28-7 (+B) - Body ground	Always	11 to 14 V

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   H28-12 (GND) - Body ground	Always	Below 1 Ω

   TEXT IN ILLUSTRATION
   
   

   *a	Front view of wire harness connector (to Door Control Receiver)

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  12

1. Reconnect the H28 door control receiver connector.
2. Measure the voltage according to the value(s) in the table below.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   H28-4 (RDA) - Body ground	Ignition switch off, all doors closed and door control transmitter switch off	11 to 14 V
   	Ignition switch off, all doors closed and door control transmitter switch on	pulse generation

   TEXT IN ILLUSTRATION
   
   

   *a	Component with harness connected (Door Control Receiver)

Result: 

NG 

REPLACE DOOR CONTROL RECEIVER 

(Refer to REMOVAL [06/2016 - ] )

Result: 

OK 

See step  13

1. Disconnect the D6 main body ECU (network gateway ECU) connector.
2. Disconnect the H28 door control receiver connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   D6-7 (RDA) - H28-4 (RDA)	Always	Below 1 Ω
   D6-6 (PRG) - H28-5 (PRG)	Always	Below 1 Ω
   D6-7 (RDA) or H28-4 (RDA) - Body ground	Always	10 kΩ or higher
   D6-6 (PRG) or H28-5 (PRG) - Body ground	Always	10 kΩ or higher

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  14

1. Temporarily replace the door control receiver with a new or normally functioning one (Refer to REMOVAL [06/2016 - ] ).

Result: 

NEXT 

See step  15

1. Perform the Registration procedures (Refer to REGISTRATION [06/2016 - ] ).

Result: 

NEXT 

See step  16

1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

   OK

   Doors can be locked and unlocked with transmitter.

Result: 

OK 

END (DOOR CONTROL RECEIVER IS DEFECTIVE) 

Result: 

NG 

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) 

(Refer to REMOVAL [06/2016 - ] )