LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2019 >> Corolla LE >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Dynamic Radar Cruise Control System - Diagnostics - Introduction (Model Code: ZRE172) >> Dynamic Radar Cruise Control System >> How To Proceed With Troubleshooting [08/2016 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

How To Proceed With Troubleshooting [08/2016 - ]: Procedure

  1. VEHICLE BROUGHT TO WORKSHOP 

    Result

    Proceed to
    NEXT

    Result:  1

    NEXT 

    See step  2

  2. INSPECT BATTERY VOLTAGE 
    1. Measure the battery voltage with the ignition switch off.

      Standard Voltage

      11 to 14 V

      If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  3

  3. INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)* 
    1. Adjust the reflector height.

      Refer to ADJUSTMENT [08/2016 - ]

    2. Place the reflector.

      Refer to ADJUSTMENT [08/2016 - ]

    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Turn the cruise control main switch (ON/OFF) on.
    7. Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.
    8. Check the amount of misalignment and make a note.

      Body Electrical > Pre-Collision 2 > Utility 

      Tester Display
      Front Beam Axis Misalignment Reading
    9. Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.
    10. Check the amount of misalignment and make a note.

      Body Electrical > Pre-Collision 2 > Utility 

      Tester Display
      Front Beam Axis Offset Reading
    11. Calculate the "Dealership Axis Offset Angle (with On-line Calibration Angle)" using the values "Front Beam Axis Misalignment Reading" and "Front Beam Axis Offset Reading".
      1. "Dealership Axis Offset Angle (with On-line Calibration Angle)" = "Front Beam Axis Misalignment Reading" - "Front Beam Axis Offset Reading"

        Standard

        Dealership Axis Offset Angle (with On-line Calibration Angle) 

        Vertical -2.2 to 1.6 deg.
        Horizontal -0.6 to 0.6 deg.

      Result

      Result Proceed to
      The dealership axis offset angle (with on-line calibration angle) is within the specified range. A
      The dealership axis offset angle (with on-line calibration angle) is not within the specified range. B

    Result:  2

    B 

    See step  12

    Result:  1

    A 

    See step  4

  4. CHECK CAN COMMUNICATION SYSTEM* 
    1. Using the Techstream, check that the CAN communication system is functioning normally.

      Refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2016 - ]

      Result

      Result Proceed to
      CAN communication system DTCs are not output A
      CAN communication system DTCs are output B

    Result:  2

    B 

    GO TO CAN COMMUNICATION SYSTEM:  HOW TO PROCEED WITH TROUBLESHOOTING [08/2016 - ] 

    Result:  1

    A 

    See step  5

  5. CHECK METER / GAUGE SYSTEM* 
    1. Use the Techstream to check if the meter / gauge system is functioning normally.

      Refer to DTC CHECK / CLEAR [08/2013 - ]

      Body Electrical > Combination Meter > Trouble Codes 

      Result

      Result Proceed to
      Meter / gauge system DTCs are not output A
      Meter / gauge system DTCs are output B

    Result:  2

    B 

    GO TO METER / GAUGE SYSTEM:  HOW TO PROCEED WITH TROUBLESHOOTING [08/2016 - ] 

    Result:  1

    A 

    See step  6

  6. CHECK VEHICLE STABILITY CONTROL SYSTEM 
    1. Use the Techstream to check if the vehicle stability control system are functioning normally.

      Refer to DTC CHECK / CLEAR [08/2015 - ]

      Chassis > ABS/VSC/TRAC > Trouble Codes 

      Result

      Result Proceed to
      Vehicle stability control system DTCs are not output A
      Vehicle stability control system DTCs are output B

    Result:  2

    B 

    GO TO VEHICLE STABILITY CONTROL SYSTEM:  DIAGNOSTIC TROUBLE CODE CHART [08/2016 - ] 

    Result:  1

    A 

    See step  7

  7. CHECK FOR DTCs (DYNAMIC RADAR CRUISE CONTROL SYSTEM) 
    1. Check for DTCs and note any codes that are output.

      Refer to DTC CHECK / CLEAR [08/2016 - ] 

      Powertrain > Radar Cruise1 > Trouble Codes 

      Powertrain > Radar Cruise2 > Trouble Codes 

    2. Clear the DTCs.

      Refer to DTC CHECK / CLEAR [08/2016 - ] 

      Powertrain > Radar Cruise1 > Clear DTCs 

      Powertrain > Radar Cruise2 > Clear DTCs 

    3. Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

      Refer to DTC CHECK / CLEAR [08/2016 - ] 

      Powertrain > Radar Cruise1 > Trouble Codes 

      Powertrain > Radar Cruise2 > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTCs are output B

    Result:  2

    B 

    GO TO DTC CHART:  DIAGNOSTIC TROUBLE CODE CHART [08/2016 - ]  

    Result:  1

    A 

    See step  8

  8. PROBLEM SYMPTOMS TABLE 

    HINT: 

    Refer to Problem Symptoms Table.

    Refer to PROBLEM SYMPTOMS TABLE [08/2016 - 08/2017] Refer to PROBLEM SYMPTOMS TABLE [08/2017 - ] 

    Result

    Result Proceed to
    Fault is not listed in Problem Symptoms Table A
    Fault is listed in Problem Symptoms Table B

    Result:  2

    B 

    ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE 

    Result:  1

    A 

    See step  9

  9. OVERALL ANALYSIS AND TROUBLESHOOTING* 
    1. Data List / Active Test

      Refer to DATA LIST / ACTIVE TEST [08/2016 - ] 

    2. Operation check

      Refer to OPERATION CHECK [08/2016 - ] 

    3. Road test

      Refer to ROAD TEST [08/2016 - ] 

    4. Terminals of ECU

      Refer to TERMINALS OF ECU [08/2016 - ] 

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  10

  10. ADJUST, REPAIR OR REPLACE 
    NOTE:

    When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

    Refer to ADJUSTMENT [08/2016 - ]

    Result

    Proceed to
    NEXT

    Result:  1

    NEXT 

    See step  11

  11. CONFIRMATION TEST 

    Result

    Proceed to
    NEXT

    Result:  1

    NEXT 

    END 

  12. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY 
    1. Perform millimeter wave radar sensor assembly adjustment.

      Refer to ADJUSTMENT [08/2016 - ]

      Result

      Proceed to
      NEXT

    Result:  1

    NEXT 

    See step  4

scientia non olet · About LEMON Manuals